Question about Stanley Quick-Square Layout Tool 46052 16-1/4 inch

1 Answer

Has anyone got a manual for a stanley 46-052 roofing square???

I'm after the manual as i'm trying to find out how you get from the angle of the plumb/seat cut on a common rafter to the angle for the hip plumb/seat cut?????

Posted by Neil Johnson on

Ad

1 Answer

jfhinton45

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,506 Answers

Call the Stanley service number

Posted on Oct 15, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I read the roof pitch on the Stanley 46-071 square


If you have access to your attic measure out 12" from edge, then measure straight up from there to roof and that will give you the pitch.

Dec 03, 2014 | Air Tools & Compressors

2 Answers

How can I stop a RN46-1 from jamming


We often see jamming with stainless wire collation - the problem is almost never the gun, it is because the stainless wire is much harder to shear off than regular steel. I would suggest trying another brand of nail and see if that helps.
Also, yes, the trigger is all that is required to change it to sequential, it is a very easy swap.

Jun 15, 2014 | Stanley Bostitch Rn461 Gun Coil Roofing...

1 Answer

What do all the numbers on a framing square mean and how do read them?


The numbers on the side of a framing square are used for many things. The small leg allows you to quickly lay out a wall on16" centers. The other rows of numbers help you figure the correct sizes to cut for hip roofs (roofs that have slope on all four sides.)You can get an instruction Manual from Stanley or it may be availabile on the net. Google (framing square instructions)

Aug 05, 2013 | Stanley Homeowner Carpenters Framing...

2 Answers

Looking operators manual for stanley bostitch rn45b


Look here for manual and parts:http://www.bostitch.com/default.asp?TYPE=STATICLEFT&PAGE=tooldoc_results.htm&Left=left_tooldoc_results.htm&partNum=WM45B&serialNum=

The two lines of address above should be all one line in the address bar. If it does not work, go to www.bostitch.com , service parts and find wm45b. Good luck

Sep 18, 2010 | Stanley Pneu Roof Stapler

1 Answer

How do you determan the 1 to 12 angle marks on the square to find the right compound cuts cheers


The 1 to 12 marks are the rise of the roof pitch in 12 feet. 1 would be 1 foot rise in 12 feet, 2 would be a 2 foot rise in 12 feet and so on to the max of 12 foot rise in 12 feet.

Feb 02, 2010 | Stanley 46 - 050 10 - 3/4" x 6" Quick...

1 Answer

Directions on how to use a square to cut common rafters we have a stanley squ and no manual, on use


A standard square is used primarily for drawing 90 degree angles. Simply hold the fat side of your square firmly against the length of rafter. The skinny side of the square should be lying accross the rafter, forming a 90 degree angle with the side. Use a pencil to draw a line along the edge of the square and use this line as a guide while sawing the rafters.

Sep 27, 2009 | Carpenter Stanley 45-500 Handyman Steel 's...

1 Answer

Need to know how to figure a rafter cut


Assuming you already know the angle you require, take the edge with the level on it(if you have that model) or the side that hangs over and hook it on the edge of the board. If you look at the top, on the 90 degree end, it says "pivot", and that is where you will spin the square around. You read on the 45 degree end that was hooked to the board for you angle. If you are trying to cut a rafter at a specific pitch such as a 6/12 you will spin the square around until the 6 on the Common scale lines up with the edge of the board. The Hip/Val scale is for cutting hips and valleys for the roof structure.
If you have any other questions, feel free to contact me here

Bob

Sep 11, 2009 | Swanson Speedlite Level Square

1 Answer

How to use the stenley roofing sqaure?


take your board make a mark on the side of board put your speed square on that mark(the squared side)flat up agianst the board rotate the square until the 15 deg comes to the other side of board then make your line.

Apr 06, 2009 | Stanley 46 - 050 10 - 3/4" x 6" Quick...

Not finding what you are looking for?
Stanley Quick-Square Layout Tool 46052 16-1/4 inch Logo

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Vernon Taylor

Level 3 Expert

7163 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...