Question about Kenmore Oasis HE 27082 Top Load Washer

Open Question

How do I reset a Kenmore top loading oasis washing machine

Posted by Anonymous on

Ad

5 Related Answers

SOURCE: Kenmore Oasis Washing machine makes noise during Spin cycle

with the machine empty see if you can lift up only the tub and see if it drops down.check to make sure there is nothing between the tub and outer tub have you gotten an f-51 error?

Posted on Nov 11, 2008

Ad

Anonymous

  • 23 Answers

SOURCE: water leaking from bottom ofoasis top loading machine

you may not be leaking out the bottom. Your stand pipe may be clogged. If the stand pipe has a slight clog in it, the stand pipe will over flow, and the water "looks" as if its leaking from the bottom... These pump faster than your old machine, so the pipe will back up faster... hope that helps

Posted on Jul 31, 2009

Ad

Anonymous

  • 572 Answers

SOURCE: In mid wash the Kenmore Elite Oasis HE flashes F51 and

check if basket turns freely. if it does replace the main board

Posted on Feb 06, 2010

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: getting LF reading on kenmore elite oasis HE top

LF Error code: LF stands for long fill and occurs when the water level does not change for a period of time after the valves are turned on.

All washers are designed to operate with a water supply pressure of 20-100 PSI. When the pressure drops below 20 PSI the washer can have the following problems:

* Slow Fill- low water pressure reduces the speed at which water flows into the machine.
o Verify the pressure at all other water sources in the house (i.e. sinks, showers, etc..). If you find other places where the pressure is low, the problem is not with the machine but with the water supply.
* Continuous Fill- The valve may not fully seat under 20 PSI which would allow for a constant flow even when the machine is not supposed to be filling.
o Contact the water company to verify the pressure being supplied to the house.
* dispenser- Needs a minimum amount of pressure to function. May dispense constantly, at the wrong time, or not at all.
o A plumber may need to be consulted if the pressure is found to be too low.

Things you can check :

* Are the Hot and Cold water faucets turned on
* Are the water hoses kinked
o Make sure all the hose are straight and able to flow water
* Are the screen inside the water valve plugged
o Inlet valve should be free of debris and rust.
o Turn off water and remove the inlet hoses from washer.
o Remove any accumulated film or particles.
o Assure rubber washers are in the end of each inlet hose.
o Reinstall hoses, turn on water and check for leaks.

Error codes can be caused by a Power Surge or other electrical anomaly,attempt to return the washer to operation by following the Hard Reset procedure below.

1. Unplug or turn the circuit breaker off for 30 seconds.
2. Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
3. Press the Pause/Cancel/Stop button twice to clear the display.
4. Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 19, 2010

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: Kenmore Oasis washing machine is giving me a UL

It appears your load balance sensor has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I reset Kenmore elite oasis he washing machine


You can download the manual at the link below but you need the model number. The site can also tell you where to find the model number. User Manual Downloads

Aug 03, 2014 | Kenmore Oasis HT 4.7 cu. ft. Top-Load...

1 Answer

How to reset my Kenmore elite oasis he washing machine


NORMALLY JUST UNPLUGGING IT FOR A FEW MINUTES SHOULD RESET IT, UNLESS U WANT TO RESET THE ERROR CODES

Aug 03, 2014 | Kenmore Oasis HT 4.7 cu. ft. Top-Load...

1 Answer

Kenmore oasis HE Top load Washer stopped in the middle of a cycle. No power and will not unlock


error code? totally unresponsive? try reseting power then if unresp. replace main control. verify 120v into board. 3 screws on rear of console and lift.

Sep 16, 2012 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

What happen when A kenmore oasis he washer has no power. Is there A reset button


In them tech sheets is some info on what to do in case that puppy appears to be dead in the water. OASIS TECH SHEET

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jun 16, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Oasis HE 27082 Stainless Steel Top Load Washer: how do i soak whites in a kenmore elite oasis?...


There is not a program - you have to do it manually on this machine.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 17, 2010 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

What problems are generaly experienced with the Oasis top load washing machines???


The easiest way for you to find out what problems the Oasis is having is to type Kenmore Oasis in the Find a Solution area of the Fixya main page.

Then you'll see a list of the problems that others have had and the solutions posted by others at Fixya.


I'd also Google Kenmore Oasis and you may see other areas of concern.

Apr 08, 2010 | Kenmore 4.5 cu. ft. Oasis Canyon Top Load...

1 Answer

Kenmore Oasis HE shakes violently during spin cycle


Machine legs should be adjusted so that machine is level and standing on all four legs. The load in the machine should be evenly distributed. Utube has an excellent video on washing machine repair.

Nov 20, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Machine stops several times shows F1 code


this is a main control board failure and needs to be replaced

Sep 16, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Oasis washing machine is completely dead


discconect power for about 10 minutes,, then plug it back in should fix if not call repair possible control board failure ,,,,,,

Jul 18, 2008 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

Related Topics:

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Will Mishler
Will Mishler

Level 2 Expert

307 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...