Raymarine Rc435 Chartplotter Logo

Related Topics:

Question about Raymarine Rc435 Chartplotter

1 Answer

I have problems with my plotter Raymarine Rc 435 chart plotter.This plotter can not location my ship to do.What is problems?

Posted by Slaven Prskalo on

Ad

1 Answer

Craig Vohwinkle

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 97 Answers

Be sure there isn't any aluminum in close proximity to your GPS antenna, or that your antenna is not to close to other powerful electronics. Aluminium reflects electromagnetic signals and other electronics emit EM fields as well causing disruption of your GPS signal reaching your antenna.

Posted on Oct 03, 2014

Ad

2 Related Answers

Radoslav Segaric

  • 43 Answers

SOURCE: Display control unit frozen, display just reads standby

The reason is because the housingin is a little bit broken or throw the keypad water came inside yuor Display and after this the oxidation ha destroyed a part of the printid circuit or the switch of the keypad

Posted on Oct 13, 2009

Ad

Anonymous

  • 10865 Answers

SOURCE: My Raymarine 435 is showing

Hi. Here is a download of the manual http://www.raymarine.com/raymarine/SubmittedFiles/Handbooks/Navigation/81212_1www.pdf

go to page 18 to learn how to correct your issue. J.

Posted on Aug 23, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Raymarine dsm300 Circuit breaker keeps tripping g when connected to chartplotter

either the cord to the chart plotter is faulty or the chart plotter itself is dead short
have an electrician do an insulation test and circuit test on the cord and plotter unit
0helpful
1answer

System haild

Take the Raymarine Rc 435 Chartplotter to a system or computer engineer for repairs.
6helpful
1answer

My Raymarine C80 CHart plotter won't load.

Check to see if this is a power issue by connecting to shore power and fully charging your batteries overnight with instruments off. While still connected to shore power, with batteries fully charged, turn on C80 navigation system. If the loading screen comes on and does not reset, then try holding down the button immediately to the right of the red power button for at least 3 seconds to see if the system re-boots.
0helpful
1answer

The chart plotter worked perfect for 5 yeas,

I think you have a C- Map card (black colour)clean the contacts with a contactcleaner if it not works try the card somewhere else
The C-Map card have problems that they work for a while and than stops inside the card a some memorychips and they losing contact
1helpful
1answer

My plotter seems not to output NMEA to my DSC radio and auto helm

Your plotter can talk to you Radio and your pilot. It sounds like one of two things.You must go into the system setup menu and turn on the nmea sentances. You will need to turn on RMB, RMC, GGl at least. You can turn on all the sentances if you like it does not matter. If this does not fix, check color of wiring is correct. Remember you have to go from NMEA + out (on plotter) to NMEA + IN on Radio.Then you need NMEA - out(on Plotter) to NMEA - IN on Radio.
You can look at the sentances wirth a multi meter coming out of your plotter. You put meter in DCV and connect across the NMEA out lines. You will see the meter move every second or so as it send a sentance.
0helpful
1answer

Problems talking to autopilot

I think you use the NMEA output to the autopilot .
The plotter shows you only when you have a seatalkconection with a Raymarine autopilot on you Plotter
1helpful
1answer

Rl70c raymarine depth finder problem

fish finder transducer needs to be on before you boot your system. check your hsb cables and termination
0helpful
1answer

RL70CRC crashes with new "Wide" C-map cartridge

get a new burn on the chip, I have seen this issue on a particular burn.
1helpful
2answers

Raymarine RL70CRC GPSRadar

Hi Matt,

There is a feature in these chartplotters called "Plotter Mode" that is often misunderstood and causes the exact problem you describe.

Press menu.....chart setup.....and scroll to the bottom until you see Plotter Mode in the list of options. It should be set in the OFF position.

If you have more than one display networked onboard check the setting in each one invividually.

What Plotter Mode does is allows the chartplotter system to access range scales not supported on the chart. It is not normally used for map-based navigation but more so for chartless electronic plotting (it can display routes, waypoints and track-recorder breadcrumbs.) open-ocean cruising, or for ultra-precise GPS operations (like a precision anchor drop, finding a very specific location etc. When plotter mode is on you can zoom in to a very, very small working area. The indicator it is enable is the cross-hatch background on the screen, the lack of map information, and the NO CHART DATA watermark on the screen.
Not finding what you are looking for?

285 views

Ask a Question

Usually answered in minutes!

Top Raymarine Boating Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22509 Answers

Mike

Level 3 Expert

4383 Answers

Are you a Raymarine Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...