Question about Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer stop at 27 minutes with nf code How can I stop it from doing this?

I push the knob in and out and it starts again.

Posted by Anonymous on

Ad

1 Answer

t snapp

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

Nf =not filling , not enough water to machine

Posted on Sep 12, 2014

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Error code

My problem was simply that the screens where the hoses connect to the washer were clogged with rust from my well water. I cleaned them and we're back in business.

Posted on Sep 12, 2008

Ad
jsrock516

Jeff Rockwell

  • 5911 Answers

SOURCE: nf pops up on the screen & the washer stops

The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad. I hope this helps you.

Posted on May 13, 2007

Anonymous

  • 1028 Answers

SOURCE: maytag washer: knob

bad contacts in timer ..replace timer

Posted on Jun 02, 2008

Anonymous

  • 373 Answers

SOURCE: I have a Maytag Model MAH8700aww washer

The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad. I hope this helps you.

Posted on Dec 12, 2008

Anonymous

  • 132 Answers

SOURCE: Maytag washer stops during spin cycle

it seems like aproblem w motor maybe need to acouple of new carbon brush to fit in motor
i think that because it seems to me from your words that the motor only works w no load
thanks

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How many times do you turn knob on timer to set


You have to push the knob in to set it for the program you want then push it in to start the machine . You can pull the knob out at any time to stop the machine .

Apr 29, 2014 | GE WBSR3140DW Top Load Washer

1 Answer

FRONT LOAD WASHER samsung model WF338AAW/xaa


you need to sort this part out level sensor located near to the door switch and main board.
samsung-assy-dc97-03716c-ap4209074_01_l-vn1wiordb5lxotmqu1or3lil-1-0_0.jpg

samsung boardpng-vn1wiordb5lxotmqu1or3lil-1-4.png wiring will be similar to this. might have a blocked air feed from the drum don't blow into the sensor take the clear pipe off and blow down that to make sure its not blocked, washing powered and stuff can block the line.

Jan 13, 2018 | Washing Machines

1 Answer

FRONT LOAD WASHER samsung model WF338AAW/xaa


please see the cause and proceed to test the water inlet valve can be defective and replace it.use the common sense,see the diagram
God bless you
Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the preset water level after 10 Minutes or more at the time of initial water supply. The error status can be cleared by turning the POWER switch OFF and back ON.
9_20_2012_3_27_50_am.jpg9_20_2012_3_28_21_am.jpg

Sep 19, 2012 | Washing Machines

1 Answer

It stops about 13 minutes from the end of the cycle, right before it spins. It displays NF.


""It stops about 13 minutes from the end of the cycle, right before it spins. ""

NF is no fill for the FAV6800A and FAV9800A are you still having the issue.

To me it sounds like you have two issues
""It stops about 13 minutes from the end of the cycle, right before it spins. "" with no additional info this could be a issue with the Clutch Pulley. Did you take any error codes like DC or UC?

Are you going to DIY the fix or call in a repair service?

Jan 26, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Kenmore 70 Series Washer Won't advance in the


Bad timer. Try to find a used one if possible, this item is a little expensive.

Aug 23, 2010 | Kenmore Washing Machines

1 Answer

Nf is showing on the screen ans washer stops


Here is a note from the service manual:

NOTE: The machine control board will attempt to fill the washer and satisfy the pressure switch during an acumulated period of 6 - 8 minutes. If the time exceeds this time frame, the unit WILL shut down.

Having said that... First thing
1. Turn off the water at the wall connection
2. Remove the water hoses
3. Remove and clean the screens inside the water inlet valve
4. Check hoses for obstructions on EACH fitting.
5. Reinstall hoses
6. Turn on water supply at the wall connection.
7. Test machine.

The above need for cleaning happens more often than you would think.

If this does not get you going normally again just respond here and we can continue troubleshooting.

Kelly

Apr 16, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer stops during rinse cycle and isn't easily restartable....


Sounds like the contacts in the timer has a problem. Unplug washer. Remove the back of the washer and spray WD40 in the timer. Put towels around and under to to collect excess runoff.
Rrotate washer dial 25 times and spray some more wd40. Rotate 25 times again. Do a wash load. If it works put everting back together.

May 04, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Washer stopped in the middle of the cycle


sounds like motor if nothing stuck between tubs or in pump ,check these first if ok you have bad timer

Nov 12, 2008 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

993 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

606 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18193 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...