What is Error A01 ?

When you encounter flashing lights on your Hoover H dishwasher and the appliance is not responding as expected, it indicates that there might be a problem with the dishwasher's operation. The specific meaning of the flashing lights can vary based on the dishwasher model and its error code system. However, here are some general troubleshooting steps you can take:

1. Check the Manual: Refer to your dishwasher's user manual or guide. Look for a section that explains the meaning of the flashing lights and any corresponding error codes. The manual may provide guidance on what steps to take to resolve the issue.
2. Power Reset: Turn off the dishwasher and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on. This can sometimes reset the control board and resolve minor glitches.
3. Check for Door Lock Issue: Some dishwashers have a safety feature that prevents them from starting if the door is not closed properly or the door latch is faulty. Make sure the door is securely closed and the latch is functioning correctly.
4. Check Water Supply: Ensure that the water supply to the dishwasher is turned on and there are no kinks or blockages in the water inlet hose.
5. Inspect Drainage: Check the dishwasher's drainage system for any clogs or obstructions. A blocked drain can prevent the dishwasher from starting.
6. Cancel Any Previous Cycles: If there was a previous cycle that was interrupted or not completed, try canceling that cycle and then select a new cycle to see if the dishwasher starts.
7. Child Lock: Some dishwashers have a child lock feature that can prevent the appliance from starting. Check if your dishwasher has this feature and make sure it's not activated.
8. Error Codes: If your dishwasher has an error code display, note down the specific error code that corresponds to the flashing lights. Look up the error code in your manual or online to understand what the issue might be.
9. Professional Service: If none of the above steps resolve the issue and your dishwasher is still not responding, it's advisable to contact Hoover customer support or a professional appliance technician for further assistance. They can diagnose and repair any more complex issues that might be affecting your dishwasher.

Remember to always prioritize safety when working with electrical appliances. If you're unsure about any step, it's best to seek professional help.

turbid water!

Whirlpool Dishwasher Error/Fault Codes - eSpares

https://www.espares.co.uk > Advice Centre > Dishwashers
FA (or 11 flashes) - Optical water indicator (turbidity) ... This fault indicates an error with the sensor in your machine that monitors the water cleanliness. If ...

Whirlpool Dishwasher Error Codes - Lights Blinking Flashing

https://removeandreplace.com > ... > Dishwasher Repair
Mar 9, 2016 - Some Whirlpool dishwashers display an error code by flashing the clean Light on the display in a pattern.

Whirlpool ADG 7560/2 pumps in water, then beeps with error ...

https://www.reddit.com > Whirlpool > comments > dish...
3 days ago - Dishwasher - Whirlpool ADG 7560/2 pumps in water, then beeps with error and 11 flashes. My dishwasher started faulting.

..

First you have to fix where the leak is coming from that tripped to E15 error code. You can reset by turning off power for 15 minutes.

An E15 error code indicates that the safety switch has detected water in the base of the dishwasher. Your leakage protection system has activated. What can I do to fix the E15 Error Code on my dishwasher?

E15 Bosch Dishwasher Error Code

.https://www.google.com/search?q=dishwasher+e15+error

...

If you aren't sure whether Control Lock is on, press a cycle button on the keypad. If Control Lock is on, the light will blink three times.
Turning off Control Lock:

1. Press and hold the Lock Button for four seconds. The lock light will disappear.
2. Once off, you should be able to start your wash cycle.

Note: If Sleep Mode is on, turn that off first, then turn off Control Lock.


Like many other electronics, you may need to reset the dishwasher control panel by turning it off, waiting, then turning it back on.

1. Press the OFF button.
2. Disconnect the dishwasher from its power source by unplugging it or by turning the circuit breaker off at the electric panel.
3. Once disconnected, wait one minute, and turn the power back on.

Error type A01: Master feed error Error point 211: Master-positioning sensor in ON during standby.

error p986

The cover is not shut all the way or the magnet is not making the connection between the cover and the chassis. A1 is a microcode checksum error. don't know what that means.

I looked at other people's suggestions on the web and tipped the machine over to the right side at an angle of 45deg (making sure I had old towels on the kitchen floor.) Water came out from the bottom right-hand corner. When I started up the machine it worked again.

I am writing a letter of complaint to Indesit because in under 3 years I have had to call out the engineer 3 times. Twice the door dropped on it's hinges and just a week ago, when opening the door, the board with all the electronics came away.

This is the first time I have had a malfunction as such and was amazed that a list of error messages was not in the handbook!

I shall not be buying an Indesit again. I have had a Zanussi washer/dryer for 15 years at least. It has had a new door but is still going strong.

REPACE FLOAT SWITCH

Error message A01 means -Acqua stop operated due to a leak or overfill. Check if there is still water in the machine after it stop pumping. In case you still have water - your problem is with the pump or with a blockage drain line. If there is no water in the machin, it might be a water level sensor issue - stuck physically in the high level position or become defective. Try to reduced the water presure and leveled it up by the water entrance tap to the machine, it might solve your problem. Goog luck !!