Question about Exercise & Fitness

1 Answer

I just recently purchased an Xterra Elliptical F420.e and it's making a clicking sound in the wheel. How can I fix this problem?

Posted by Lori Alvarez on

Ad

1 Answer

Cesare Cesaretto

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check out this website for more informations:
your-worokout-routine.com!

Posted on Sep 08, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Broken axles on elliptical trainers


I would call and get the prices, if you do the work it is cheaper than replaciong them.

Mar 15, 2014 | Exercise & Fitness

1 Answer

Elliptical resistance


Be aware that the resistance is often the part that requires repair. Resistance is managed magnetically, so often if the machine is working, but the resistance isn't setting correctly or at all, check the bolts that secure the magnets. If they are loose, the resistance will slip. If the bolts are fine, check the magnets themselves by using a refrigerator magnet and see if it is attracted or repelled by the your fridge magnet. If not, the magnets have de-magnetized and need to be replaced.

God bless you

May 22, 2013 | Xterra Fitness Xterra FS220e Elliptical...

1 Answer

My Schwinn 430 elliptical makes a clunking noise when pedalling backwards but not forward. What is causing this?


I have a iron man cdt elliptical that was clunking . I found a shaft on the end of the crank was slipping in and out, inside the bearings. I shimmed it and retightened the retaining washer which prevented it from slipping . Smooth as silk now. It was very frustrating because all seemed tight at first.

Nov 10, 2012 | Schwinn 430 Elliptical Trainer

2 Answers

NordicTrack CX 1055 Elliptical ramp pedal wheels


Hi, You can find them easily on amazon, click here ant take a look: Amazon com Elliptical ramp pedal wheels. Wish you best of luck. Cheers

Jun 22, 2012 | Exercise & Fitness

1 Answer

Turn key in ignition of Xterra 2002 it makes a moan sound


When the design of starters (NipponDenso) in these cars fail to crank the engine over they most often make a clicking noise but don't turn the engine over, what you may have going on here is a poor connection at the starter, disconnect the battery negative cable and go under the truck and loosen and then tighten the starter connections, all of them and see if that cures the problem. If that doesn't remove the starter and replace the starter solenoid assembly, it most likely can be purchased separately.

Dec 30, 2011 | 2002 Nissan Xterra

1 Answer

A friend recently gave me a ProForm 700 treadmill that folds up & the front left side of what appears to be the belt or possibly the rotor sounds like dolphins talking when you turn it on. How can I...


dEAR Sir:

I will help you inmediately.

HOW TO LEVEL THE ELLIPTICAL CROSSTRAINER:

After the elliptical
crosstrainer has
been moved to
the location
where it will be
used, make sure
that the ends of
both stabilizers
are touching the
floor. If the elliptical
crosstrainer
rocks slightly during use, turn one or both of the leveling
feet under the front stabilizer until the rocking
motion is eliminated.

2) You must put a little oil ( tree in one oil) +a little grease in the rotor shaft.

Hoping that you fix this, anyway if you need some extra help, contact me.sincerely.

blessing.

E.CUADRA
Managua, Nicaragua C.A.

Sep 13, 2011 | Proform CrossWalk TreadSoft Treadmill

1 Answer

There is a clicking sound periodically coming from the right pedal while I use the machine (Precor 546i). I tried tightening the bolts but the clicking persists. Any thought would be greatly appreciated....


It sounds like it could be a faulty bearing in one of your wheels, a worn ramp or a combination of the two. The following link will take you to our Precor page. Please reference your model and serial number. This will allow you access to the correct parts and manuals for your machine.

Precor Elliptical EFX Repair Parts Belts Wheels Pedals SPORTSMITH net

Aug 06, 2011 | Precor EFX 546i Elliptical Version 4

1 Answer

2001 Xterra makes a clunking sounds when I make a hard left turn


Most likely the cv joints need to be replaced. Also check struts.

Jan 05, 2010 | 2001 Nissan Xterra

1 Answer

Popping and grinding with extreme wheel turns


Hi

This sounds very much like a problem with your front wheel bearings.

The Xterra Wheel Bearings need to be re-greased at least every 30k miles, and more often if you often go through water deep enough to reach the hubs. When the water gets in the hubs it contaminates the grease and damage can be done to the bearings. This will create a grinding noise and in severe cases even damage to the axle spindle.

You will need to have this looked at by a mechanic to fully assess the damage. Cost will very much be dependant on the extent of this damage.

This link gives an idea of the cost for bearings on the Xterra but obviously this does not include labor to fit. As I say the overall cost is difficult to predict until the full extent of the damage is known.

http://www.autopartswarehouse.com/search/?N=0&VN=+4294967085+4294965648+4294967179&Nr=AND(make:Nissan,model:Xterra,part:Wheel+Bearing,universal:0)

Hope this helps. Thanks for using FixYa.

Nov 20, 2009 | 2004 Nissan XTerra

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Tom Chichester

Level 3 Expert

61131 Answers

ray gallant

Level 3 Expert

71004 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...