Question about Electrical Supplies

1 Answer

How to diagnos Overcrank light

Engine starts, runs for 15 seconds and shuts off then starts again and shuts off about6 times then overcrank light comes on.

Posted by Anonymous on

Ad

1 Answer

Thomas Beaver

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,119 Answers

I don't think the over crank is a problem.
Why is it shutting off?
Find the owners manual to find out if there is some fault that will shut it down or it may be an engine problem like the choke not releasing after starting.
To find a manual online you will need the make and model number of your generator.

Posted on Aug 20, 2014

Ad

4 Related Answers

epangan29

  • 113 Answers

SOURCE: My generator runs automatically once a week. It

disconnect the battery and try again.

Posted on Nov 29, 2009

Ad
protek480

Craig Butler

  • 1730 Answers

SOURCE: overcrank error message

The 'overcrank' error simply means it tried to start but never actually started. It cranked for an extended period. Check the fuel and starting issues you would normally check to start the engine.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Posted on Jul 02, 2009

hkp7

  • 397 Answers

SOURCE: Had a bad battery and

Check for a burned fuse or tripped breaker to the cranking circuit.

Posted on Jun 27, 2011

ImJustAvg

  • 2006 Answers

SOURCE: my generac 15kw generator went

It could be either your start capacitor or the contactor-relay. Or you could try cleaning the contacts of the relay with an emery board to see if there is a change.

Posted on Sep 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fan shuts off after about 15 seconds of heat..


it don't come on at all when u turn the heater on

Dec 26, 2013 | Honeywell Heating & Cooling

1 Answer

I have an older 30KW Generac SG 030 1800rpm running on Nat Gas which I bought used. It has set up for several years. I installed a new PN0830890SRV master control board I bought from the local Generac...


need to calibrate the main control board. 83089. also is it overspeed or overcrank? if the board does not see the right rpm or is blow a certain threshold it will think it has not started yet and shut down on overcrank.

Mar 13, 2017 | Generac 13,000 Watt / 13,000 Watt Home...

1 Answer

Electronic throttle control light comes on,car starts to idle rough and rpm hand went up


I am not to sure but I know that there is a process called the "Relearn" which mainly zinchronizes the throttle body with your ECU... But I am not to sure for a ford exactly I know that for a Nissan if you getting code P0507 the relearn Process will follow as: 1. Warm up the car to normal temperature of drive it for a few minutes and turn it off. 2. After you shut off the engine wait ten seconds. 3. Turn the Key to the ON Position but don't start the car. 4. Wait 3 seconds and press the gass pedal and release 5 times in whitin 5 Seconds. 5. Give it a 7 seconds and press the gas pedal and keep it pressed for about 10-15 seconds and the engine light should star blinking for about 15-20 seconds as soon as it stops blinking start the engine let it run for about 20 seconds and rev the engine up a couple of times then you can shut it off.
But I had a couple of time in which a rebuild piece might fail to sync with the relearn process...You might need to go with a new part....Good Luck. I am kind of sure that Ford migh have a forum those sites are very helpful because of they are Ford Vehicles owners that will post their solutions to similar issues.


Good Luck! CR.

Mar 15, 2010 | 2006 Ford Mustang

1 Answer

Hi I have 2000 BMW 320i. Lumpy idle when cold and oil light for


Your oil is a little low, and the timing may be off a bit but if it smooths out after warm it is probably ljust
low oil.

Jun 29, 2009 | 2000 BMW 3 Series

2 Answers

Overcrank error message


The 'overcrank' error simply means it tried to start but never actually started. It cranked for an extended period. Check the fuel and starting issues you would normally check to start the engine.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Mar 31, 2009 | Kohler 12 kW Emergency Power System -...

1 Answer

Takes multiple times to start


I think you have a faling fuel pump or a bad pressure regulator allowing fuel pressure to bleed down when the engine is off.
Try this test - When you start the car for the first time of the day, turn the key to "ON", wait a few seconds, turn the key off. Wait about 15 seconds, turn the key to "ON" again, wait a few seconds. Then wait one final time for 1 seconds and try starting the car. If it starts right away, that means fule pressure is bleeding of due to a bad check vavle int he fuel pump, a bad fuel pump or a bad pressure regulator.

The reason for the procedure is because when you turn the key to "ON", the fuel pump runs for 2 seconds and then shuts off if the engine is not running. The 15 seconds wait is for the power and fuel pump relay to cycle off before it will run the pump again.

Let us know how the test comes out. The fuel pump is in the fuel tank and hums when it is running.

Mar 01, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Key stuck in ignition


Be sure its all the way in park or try neutral.Its possible that security system does not recognize the key. Is security light flashing or on steady? Shut all doors and windows,trunk,hood, turn off all accessory's,roll down drivers window, turn key off and remove for at least 1 minute, insert key into ignition, try to start leaving key to run position for 20 minutes, turn key to off,wait 15 seconds, try to start again leaving key to run, wait 20 minutes, turn key off,wait 15 seconds, try to start, again leaving key to run, wait 20 minutes, turn key off, wait 15 seconds, try to start. This should relearn key code. It may relearn after 1 learn cycle and start if system is ok. Hope this helps and that the weather is dry and warm for this procedure! This is not always a fix, but works most of the time.

Jan 25, 2009 | 2006 Chevrolet Monte Carlo

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

770 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrical Supplies Experts

Gene Haynes

Level 3 Expert

5391 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18397 Answers

Are you an Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...