Samsung calibration how do I get the "user settings" menue off the screen of my TV. Stations don't show. Searched the manual and found nothing.

To connect your Spectroniq PLTV 32050 TV to your Dish Network receiver and program the stations, you can follow these steps:

1. Connect your Dish Network receiver to your TV using an HDMI or RCA cable. Make sure the TV is turned on and set to the correct input source.
2. Turn on the Dish Network receiver and follow the on-screen instructions to complete the setup process.
3. Use the Dish Network remote to program the stations. Press the "Menu" button and navigate to the "Programming" or "Channels" section. Follow the on-screen instructions to scan for available channels and save them to the receiver.
4. Once the channels have been saved to the receiver, use the "Input" or "Source" button on the TV remote to select the input source that the Dish Network receiver is connected to.
5. Use the TV remote to adjust the picture and sound settings to your preference.

If you have any trouble with the setup process, you can refer to the user manual for your Dish Network receiver and your Spectroniq PLTV 32050 TV for more detailed instructions.

Try hard reset, Please unplug the tv cables and power cables for 30 min and redo the cable and check its working ....




Good luck...

Refer its user manual for details. https://www.ebookjos.com/pdf/samsung-la26r71bd-owner-manual-guide.pdf Check this link to download the user manual to this set; if you haven't it with you now.
Electro help

Are you pressing menu button on the monitor or the DVR?
Your problem may not be the cameras, but between the DVR and the monitor. Found this on page Eng-19 of the user manual which I found on Samsung.com
This monitor was set to password lock when you purchase a new set. Therefore, you must first enter a 4 digit password to activate the On Screen Display... the default password is 4321. Not sure if that helps.

There is a radio option to recalibrate your touch screen. Please press the following three hard keys simultaneously RADIO/MEDIA, SEEK UP, NAV (AUDIO on REN). Once you begin to recalibrate the touch screen you must finish. Audio confirmation prompts are provided for each of the three points of calibration, one beep for the first, two for the second and three for the third. The calibration needs to be precise as possible and a PDA stylus would be recommended. The MyGIG radio requires the user to repress each calibration point to confirm the calibration process. A green crosshair indicates proper calibration.You must not start with the "+" but with the "+1", then goto "+2" and last to "+". Repeat this until all crosses are green and exit with pushing the menue or any other key. Done

Touch screen problem

If your touch screen is not working, there's just 2 major causes of such, either a hardware cause which might be either the phone falling on a hard object or in water which could damage the sensor board and either the screen is malfunctioning and needs to be calibrated.
If you can access the menu of the phone, i will advice you calibrate the screen first before you send it to a repair shop. There is no updates to download for such problem as updating the firmware of the phone would do nothing but change the settings of the phone.
To calibrate the screen, you will have to go to the phones menu, go to settings, then you select the calibrate screen, it will show you some stars to touch and once you touch them properly, then your screen will be able to work effectively.
But if you cannot access the menu because of the touch, then i will advice you send it off for repairs, and what to repair on the phone is the sensor board.

Hope this helps you.

You only have the preset picture settings and the custom settings to use in the user menu.. Only your eyes can tell you what you like. The only other way to get a really killer picture is to have a Professional ISF Video Calibrator calibrate the set.

To get any HDTV to work this is what you have to do;
CHANNEL section
1) Connect your antenna cable which you have done.
2) Go into the menu to the source option and select AIR/ANTENNA since you are using an antenna.
3) In the menu you will have to SCAN in the stations. This auto program will find all available stations.
Now you can watch tv by selecting the station you want.
The new generation of HDTV is different from the old analog sets. These have to be set up to work.
Exact information can be found in your Users Manual.

Press "HOME MENU" select "INITIAL SETUP" and advance forward to "CLOCK SETTING'.

Enter your time manually OR

Select * "AUTO"

*Some stations embed the proper time within the transmitted signal. Your Pioneer will calibrate it's clock according to your local studio time.

I found a full users manual online and I looked for a place to post it here, but I found no place to do so. Sorry.

Hope this helps!

look for user manuals at http://www.user-manual-search.com