Question about Honeywell HZ322K TrueZONE Kit with DATS, Transformer and HZ322 Panel

1 Answer

Who has torque marks specs requirment documention

Posted by Anonymous on


1 Answer

Greg Scott

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 116 Answers

That information will be proprietary per manufacturers.
This can help guide you. If you need larger than an ME, do a specific search

Posted on May 12, 2018


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

What is the torque onbolts?

The torque specs, of all bolts that require tightening to a specific value, are found in the repair manual of the vehicle that your working on, also most bolts have lines marked on the head that indicate torque value. What are you working on?

Nov 30, 2015 | Cars & Trucks

1 Answer

What's the outer tie rod end torque specs for 2000 Dodge Dakota sport ?

this was copied off of the following link. should be same torque requirments-
this is off a 2004 manual,which should be real close if not exact

1. Align reference marks and install pitman arm.
2. Install the lock washer and retaining nut on the pitman
shaft and tighten nut to 251 N·m (185 ft. lbs.).
3. Install the drag link (1) to the pitman arm (5). Install
the nut (4) and tighten to 54 N·m (40 ft. lbs.) Then
an additional 90°.
4. Remove the supports and lower the vehicle to the
surface. Center steering wheel> and adjust toe,
5. After adjustment tighten tie rod adjustment sleeve
clamp> bolts to 61 N·m (45 ft. lbs.).
NOTE: Position the clamp on the sleeve so retaining
bolt is located on the bottom side of the

got it from here -

Tie rod end torque spec DodgeTalk Dodge Car Forums Dodge Truck Forums and...

Feb 23, 2015 | Dodge Cars & Trucks

1 Answer

Torque specs for head bolt on a 1999 harley flsts

Oil bolt threads.
Tighten head bolts in an "X" pattern.
Tighten bolts to 7-9 ft/lbs
Tighten bolts to 12-14 ft/lbs
Using a Sharpie type pen, make a vertical mark on the bolt head and a matching mark on the cylinder head next to it.
Tighten each bolt 1/4 turn, using marks as a guide.

That's it!

Sep 14, 2014 | Motorcycles

1 Answer

Torque specs head gasket

Mitsubishi Specifications for head torque and order

Page 64 of online document should have your information.

The torque order illustrations are at the end of the this online .PDF document. Find your specific vehicle on page 64 and locate the specified torque order diagram number that it shows. Then head to the diagram illustration they posted at the end of the document.

Sep 01, 2013 | Mitsubishi Cars & Trucks

1 Answer

I need to know how to find/set timing marks for 2002 Kia Sedona and head bolt torque specs

The head bolt torque on a 2002 Kia Optima is 45 ft/lbs of torque. Always make sure you use a good torque wrench to get it right. ------------------------------------------------------------------------------------
Original Launch X431 Master

Mar 13, 2013 | Cars & Trucks

1 Answer

Need cylinder head gasket torque specs.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Sep 18, 2009 | 2000 Ford Focus

1 Answer

Need torque specs for the pinion nuton rearend!!!!!!

If your car is a rear wheel drive, and you mean the nut that's just after your drive shaft, then...If you are replacing the seal, you need to mark the nut and the shaft so that when you re-assemble it you tighten the nut just a 1/4 " past the original mark. The reason is there is a crush collar that compresses inside on your pinion shaft to give it a little resistance. This is measured using a beam type inch pound torque wrench. I hope this might answer some questions. Setting up a pinion once removed requires a new crush collar, and the inch pounds of resistance are a little different between new bearings, or if you reuse the old ones.

Jul 10, 2009 | 2000 Chevrolet Camaro

1 Answer

Torquing head

The 98 Corolla has a "torque-to-distance" spec.

First, torque all 10 bolts to 36 ft lbs (49 NM or 500kgf-cm), in a clockwise fashion, starting with the 2 center bolts.

Second, mark the bolts with a paint mark, and then torque each of the 10 bolts an additional 90 degrees.

Hope this helps, and thanks for choosing FixYa.

Nov 15, 2008 | 1998 Toyota Corolla

1 Answer

1998 Lincoln Mark viii Transmision Pan Torque Specs?

not needed just use a 1/4 inch drive just a bit over hand tight if u need the spec it is 25 inch pounds

Jul 16, 2008 | 1998 Lincoln Mark VIII

Not finding what you are looking for?
Honeywell HZ322K TrueZONE Kit with DATS, Transformer and HZ322 Panel Logo

Related Topics:

1,074 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Renewable Energy Experts

Greg Scott
Greg Scott

Level 2 Expert

116 Answers

Lukas Alexander

Level 1 Expert

21 Answers

Are you a Honeywell Renewable Energy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides