Question about Bunn ULTRA-2 PAF HPR GP, WHT/SST

1 Answer

What would cause my display to not work? - Bunn ULTRA-2 PAF HPR GP, WHT/SST

Posted by kellie mcglosson on


1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Bunn Master
  • 2,239 Answers

If nothing works on it, the transformer inside the right side panel needs to be replaced

Posted on Jan 28, 2015


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


see the next causes and remedy and fix it. God bless you


E7- 1) Alternative Elevation Motor

1)Cause: Elevation Motor not moving Solution:Check Elevation Motor connection

2)Cause: Elevation Elevation Motor screw binding Solution: Clean screw and lubricate

3)Cause: Elevation Motor Motor out of Range Solution: Check motor out of elevation

4)Cause: E-Motor Potentiometer: Solution: Replace Elevation Motor


Display Doesn't Light Up: a)Cause: On/Off switch Solution: Test unit is turned on b)Cause: Insufficient Power Source Solution: Plug dedicated120V, 20Amp Outlet

c) Cause: Line Cord Damaged Solution: Replace Line Cord

d)Cause: Fuse Solution: Check Fuse on MCB


Nov 13, 2012 | Treadmill Doctor Nordictrack Powertread...

1 Answer

Lcd display only works flat against camera

The ribbon wire from the display to the system board has cracked causing intermittent operation when moved. Depending on the wire configuration to the screen will decide if the screen must be replaced or the ribbon wire.

Apr 02, 2012 | Video Cameras

1 Answer

No display but fan works whiles the monitor remains yellow

Causes : It caused by cracking of Screen Display.. Solution : There is no way to repair.. to solve the problem you need to change your Display set... thanks

Aug 29, 2011 | Biostar 945GC-M7 Te Motherboard

1 Answer

I have a Merlin Magix 4424LD+ phone and the display not working. I bought a new one to replace it but the display did not work either? Is there any programming caused this display to be off or stop...

Just to verify are you using a 4wire cable that has power? If you have moved environments it is possible you might have to get the aux ac power adapter that you plug your cables into to power the display.

May 18, 2011 | Avaya Merlin Magix 4424D+ Telephone

1 Answer

We have a Compaq CQ60 laptop with display issues. Display only works at certain angles. Moving toward open or closed causes loss of horizontal sync. Screen is still bright. External display is unaffected...

you may have a bad inverter of bad inverter connector....or the connector is loose.. this can cause perminant damage if left untreated. most likely you may have a loose connection,,are you under warranty?

Dec 02, 2010 | Compaq Presario CQ60-220US PC Laptop

1 Answer

Iphone dim display , phone works fine otherwise

Hi, did the phone fall on the flow or hit something? If yes, that might have been the cause of the dim display. Cause the screen has been affected and you will need to replace the screen.

After dim display, if the phone blinks or show some funny moving display, that means is the flex that connects the front screen board to the main board of the phone that is faulty and it will need to be replaced.

Take care.

Jun 08, 2010 | Apple iPhone 3G Black Smartphone

1 Answer

Pc powers on but no display(light on board and fan is working)

Could be a loose Display Card... pretty rare that would happen if the System has been working fine. An event would have to occur to knock it out.
The PC should boot to the BIOS with everything unplugged in the System. Try to re-seat the Display Card first if not, unplug the Hard Drive to see if that is causing the issue. If you have an On-Board Video... pull the Display Card to see if you get a Boot.
Pull Modem as well...
If it were Memory you would get a beep. Wouldn't hurt to clean and re-seat Mem as well while your in there. Dust does cause errors because of poor connections. :)

Jan 07, 2010 | Shuttle (sn41g2b (black)) PC Desktop

1 Answer

Television display

This normally causes by failure of power supply board. Some time it causes by failure of inverter board, in this case you can see the picture moving on the dark screen as it has no back light.

Aug 18, 2009 | Samsung LN-T4071F 40 in. LCD HDTV

1 Answer

No power. led display very dim

dim display on an ag-1980 may be caused by bad display module or bad electrolytic capacitors in the display power supply. "no power" is probably a bad 12 volt regulator on the main board. the main power supply is working as evidenced by the display lighting up.

Jul 03, 2009 | Panasonic AG-1980 S-VHS VCR

5 Answers

Iphone display

keep the home button and the power button pressed together untill a yellow triangle appears on your screen and it will restart............this should solve ur problem.
I tried it and never saw a yellow triangle but it rebooted the phone and it worked again!
I just don't know why the screen goes blank

Jul 30, 2008 | Apple iPhone Smartphone

Not finding what you are looking for?

Related Topics:

1,124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bunn Home Experts

john h

Level 3 Expert

23438 Answers

Tom Chichester

Level 3 Expert

57285 Answers

Brad Brown

Level 3 Expert

18438 Answers

Are you a Bunn Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides