Question about Whirlpool LSR5132PQ Top Load Washer
I bought the machine last August.
Posted by Anonymous on
check the lid hinge on the LH side. the screws will come loose and then will not always engage the lid switch.
tighten the screws and if you need to you can reach under the top where the hinge is and bend it backwards to get it to engage the switch. usually the screws will take care of it.
Posted on Jan 07, 2010
I am trying to help you out here. Maybe this will help some? I am know on Fixya as the cleanup expert pro. Which means I spend my own personal time to seek out customers that maybe have not had there problem yet solved by the other fantastic great experts. I do this on my own for free. Think of me as a Specialized Trouble Shooter.
I have found out that it appears that lots of customers appreciate my efforts and help. So, I thought I would take some of my own personal time to see if I can help you. Even though this Informational site may not have your exact model or brand, But this site will help you a lot. Here is the site link about everything you want to know about washing machines and possibly yours, from repair to trouble shooting it.
Please if this helped you at all, if you can find the time and in your heart to rate my help and some kind words written would be appreciated for my free help, I would appreciate it. Like I said I just try to help, If anything this is good information for future problems. If you felt that my free help was a waist of time for you, I'm sorry. I do not get paid to help people on the site, I do it cause I like to help and maybe make a smile on someones face.
Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive, Appliance, and Electronics. Drop In anytime for my help.
Posted on Nov 01, 2011
SOURCE: Washer doesnt drain
Sd is displayed when the machine/motor control, by analyzing drag on the basket, detects a suds-lock condition, and is steady on while the control then runs a mini-clean out cycle. If the clean out cycle is unable to correct the over-sudsing problem, the cycle ends and Sd flashes in the display. This may signify:
Excessive detergent usage.
Basket cannot engage during drain step.
Mechanical friction on drive mechanism, not allowing basket to engage.
Posted on Nov 05, 2012
SOURCE: I have a wtw5600xw0 Whirlpool washer. When I press the start button the sensing light and lid lock lights turn on. Then after a few seconds the lid lock light goes off and the sensing light stays fl
Swich off the machine, try some WD40 on the door mechanism (on machine lock, not on the door) and open & shut for a minute or two. Then try the machine, spin only just to try. Source
Rate pl, if solved, or dont!
Posted on Nov 27, 2012
Check door switch: If
the lid switch is bad it will not drain or spin. Try this test: With lid open
let it finish wash cycle. Press lid switch down with screwdriver. Washer should
draining. Release switch. Motor
should stop. Press switch a second time.
Washer should start spinning as it continues to drain. If motor doesn't come on
while lid switch is pressed, replace the switch. OR
Pl click if helped.
Posted on Apr 29, 2013
Tips for a great answer:
Nov 26, 2015 | Washing Machines
Oct 27, 2015 | Washing Machines
Oct 12, 2015 | Washing Machines
Jul 07, 2015 | Kenmore 23822 Top Load Washer
Jan 03, 2015 | Whirlpool Washing Machines
Nov 27, 2012 | Whirlpool WTW5600X Washer
Oct 20, 2012 | Whirlpool LSB6200KQ Top Load Washer
I had the same problem. The lid lock assembly is broken.
If you are under warranty get it replaced. If not remove the top of the washer
and take out the switch assembly. The 4 wires going in are Yellow, Red, White,
and Blue. If you short the white and blue together, the washer thinks the lid
is closed. If you short the red white and blue together the washer thinks the
lid is closed and locked. The yellow is only there to activate the
Disconnecting the switch assembly will not work.
The electromagnet locks the lid and it also unlocks the lid. It is not a matter of cutting the power to the magnet.
Installing 2 switches that connect the red white and blue is the best option if you want to remove the lock.
The first switch should connect the white and blue. (LID CLOSED)
The second should connect the red to the white/blue connection. (LID LOCKED)
After that the lid should work.
Please post a follow-up if this works for you.
Jul 09, 2012 | Maytag Centennial 3.2 cu. ft. SuperSize...
Jul 26, 2010 | Maytag Neptune FAV6800AW Top Load Washer
61 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: