Question about Kohler Engines NEW 25HP KOHLER ENGINE CH730-3208 ZERO TURN LAWN MOWER EXMARK

2 Answers

Why exmark loses power when blades are turned on

Posted by Anonymous on

Ad

2 Answers

Neil Dignam

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Balance the blades and make sure the center piece isnt work (causing blades to shift side to side)

Posted on Mar 23, 2019

Ad

will bosaw

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 27 Answers

Check for clogged deck.also inspection of mower deck belt. Check for glazing or cracks in belt. That will slow blades down.

Posted on Aug 14, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Exmark lazer HP 19 Kawasaki 50" deck new PTO and new relays blades engage for 30 minutes then shut off engine on. After cooling will engage for 10 minutes then shut off


Engine valves need adjusting.
symptoms: starts ok, runs until engine reaches max temp loses power then stops. can't restart when hot. once restarted runs for a while stops again.

There is very little clerance in these valves and temperature alters the lenth by a few thou and the valve don't close fully losing compression, once cold the valves shrink back enough to create enough compression to start again.

Aug 13, 2015 | kawasaki Garden

1 Answer

Blade activator switch does not work


check to see if power coming out of switch if not bad

Sep 30, 2014 | Encore EXMARK LAWN MOWER HEAVYDUTY STEEL...

2 Answers

Exmark mower


you mean it dies or the engine slows down ???

Oct 19, 2013 | Garden

1 Answer

Exmark 44


When you say 'going forwaed', is that while mowing or does it do it without the blades engaged or 'not mowing'?

Jun 13, 2013 | Kohler Engines NEW 25HP KOHLER ENGINE...

1 Answer

44" Exmark lazer z pto/blade problem


My problem is that I don't know what your problem is exactly.

May 06, 2012 | Oregon Scientific Electric PTO Clutch for...

1 Answer

Metro walk behind bogging down


the springs that control carby is there leaves or grass stopping it from moving ,some lawn mowers have bad desinge for air flow off ****

Jun 02, 2010 | Encore EXMARK LAWN MOWER HEAVYDUTY STEEL...

2 Answers

A row of uncut grass left between blaces when mowing


THE answer that FINALLY worked for me. Torque the bolt that holds on the blade to the recommended torque specified in your owners manual (for my Exmark this torque is 120 ft-lbs). When I first used the torque wrench, i was quite surprised by the amount of addional force I needed to apply to reach 120 ft-lbs Exmark blades have a round blade hole with a washer and therefore, relies only on friction provided by torquing bolt to the proper torque to prevent slippage so that the blade rotates at the same speed as the spindle. When slippage between the blade and spindle occurs, blade tip speed slows leaving uncut grass.
Note: this solution will NOT work for mowers with a blade and spindle design which uses a positive means (e.g., a star shaped hole on the blade) that assures the blade rotates at the same speed as the spindle with no slippage.

Jun 15, 2009 | Craftsman 20 Hp 42" Deck Lawn Tractor

Not finding what you are looking for?
Kohler Engines NEW 25HP KOHLER ENGINE CH730-3208 ZERO TURN LAWN MOWER EXMARK Logo

1,732 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kohler Engines Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Tom Chichester

Level 3 Expert

61336 Answers

Are you a Kohler Engines Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...