Question about Sony KP-51HW40 51" Rear Projection Television

1 Answer

Projection TV Sony, first power on only hear the sound for couple second then turn off. Stand by light keep flashing 5 times. What's wrong and how to fix?

Posted by Anonymous on

Ad

1 Answer

Jason Martin

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

  • 5 times, Diagnosis: White balance failure (Not balanced) Possible causes: Video out (IC7101, 7201, 7301) is faulty (CR, CG, CB board), CRT drive (IC309) is faulty (A board), G2 is improperly adjusted. Symptoms of the problem: No raster is generated, CRT cathode current detection reference pulse output is small.

Posted on Jul 29, 2014

Ad

5 Related Answers

Anonymous

SOURCE: Sony KF-WE50

my front panel sound is not working.......?
how i can do this.?

Posted on Jan 05, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: powers on then right back of light flashes 8 times

i have a sony wide screen projection tv KP-51WS500 Red stand by light on flashs no picture

Posted on Mar 16, 2008

bestdarngood

Benjamin Patri

  • 3037 Answers

SOURCE: Sony Projection TV stand-by light keeps flashing

Many of the later model Sony TV’s have a built in self-diagnosis function. If the timer/standby indicator is blinking, this could be an indication of a problem with the unit. The diagnostic blinking will occur automatically with no action required by you to engage it.
The timing of the blinking you see would be as follows: two to nine blinks, (depending on the fault), about a third of a second apart, then a pause for 3 seconds, then the two to nine blinks about a third of a second apart again.
Here is a list of the problems that might have occurred indicated by the number of blinks. The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article.

  • Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).
  • Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective.
  • One blink - not used for the self-diagnosis
  • Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink fault. Could be a short in the power supply of any of the circuits.
  • Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink fault. This is also a problem in the power supply circuit, check T603 and R672.
  • Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505
  • Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.
  • Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.
  • Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately into safety shutdown. Check power supply regulation and horizontal circuits.
  • Eight GA_googleFillSlot("TL-IMU-Article"); blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.

  • Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not resolder as this will fix the problem temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections. Make sure the regulator is -12 or -13 (negitive).
  • Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R8051 and IC8005, also on the "D" board.
Intermittent problems? This is a great feature. You can also bring up these fault codes on-screen to see a list of the problem numbers with the abbreviation of the problem and the number of times this problem has occurred. This is slightly different than entering the service mode. To see the diagnostic screen, press the following buttons: Display, Channel, 5, volume Minus, ( not plus ) then Power. This brings up a screen with a list of the problems and number of times they have occurred. Each of the problems named, are abbreviated as, "OCP", "OVP", "V STOP", ETC. We have repeated them in parentheses in the text for the "Blinks" described above so you can correlate between the diagnostic screen and the blink codes.
Now that you know about these self-diagnostics, how do you use them? Say that you have a set with a black screen. You see that the LED is blinking four times. This would tell you that you have no vertical sweep, which is why the video is muted. If it was blinking 6 times, you would know that you have a horizontal fault. It's not a sure cure..
IMPORTANT: After you repair the unit, you MUST clear the values on this diagnostic screen. These codes do not reset themselves after the fault is corrected, so if you don't clear them, you'll be seeing "old" fault codes the next time you enter this screen. Clearing is done by going into the service mode (display, channel, 5, volume plus, then power ). Press 8 and Enter, which returns everything to the factory preset condition.

Posted on Feb 13, 2009

Anonymous

  • 239 Answers

SOURCE: Sony KDS-60A2000 projection TV: power led blinks 4 times

the projector bulb has gone out you need to replace it.

hope this helped
please rate well

If you need further help, reach me via phone at https://www.6ya.com/expert/mark_445a24324be9eb03

Posted on Mar 04, 2009

Slinteriors

Sonny Berry

  • 8617 Answers

SOURCE: 5 red flashs on power/standby light on kdsr60xbr1 screen blank,

Thats the error for lamp driver error. Which means the Ballast is most likely defective. You can get the replacement ballast for your model at the following link which comes with installation instructions.
http://servicemanuals.vstore.ca/product_info.php/pName/kdfe42a10-ballast-assembly/cName/sony-parts

Posted on May 23, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Picture and sound come and go on antenna or dvd

Try another lamp. Error 5 is Lamp power supply, but its usually always the lamp bad.
0helpful
2answers

Problem with Sony Grand Wega TV

This could be due to bad capacitors in the sweep supply, a bad High Voltage block, a bad regulator.
4helpful
1answer

My tv won't turn on anymore. The red light flashes 6 times then pauses for a couple seconds then starts flashing six times again. Just keeps doing it repeatedly

try unplugging the tv and waiting a minute and try it again if its still the same? It sounds like a Capicitor problem on the Power supply.
0helpful
1answer

Sony KP-57WS520 57 inch rear projection TV. When I turn it on I hear sound and it cuts itself off and standby light flashes 5 times over and over, if I cut it on again I hear sound and then it cuts itself...

sanschargrin,

I hate to be the bearer of bad news but your unit has some optical engine problems. Here is a web site which explains it all and tells you where to apply for class action compensation. http://sites.google.com/site/sonylcdrptvproblems/

Thanks for using FixYa and for the great rating.

hardrocko
3helpful
1answer

T.V. doesnt turn on and red light keeps flashing at Power Section

Ur power board have dead capacitors,Know how to solders?Take the tv aparts check for capacitors puff up or burst open in the power board.Replaced those capacitors.Or tries Shopjimmy.com,Ebay.com buy a refurbih power board.
0helpful
1answer

Power green light will flash then flash red when first turned on

Please intimate exact model of your Sony TV to find out reason of no power up.
2helpful
1answer

Lamp light flashing on toshiba 50" projection tv

TV tries to come on - yellow light next to power light flashes but then it turn itslef off.........It tries agin after few sceonds and sequence repeats. I can hear the sound but no video
0helpful
1answer

Sony 42in- No picture or sound

You need to replace the bulb...very easy. You can do it yourself.
0helpful
1answer

Sony KP-51WS520 Stand by flashes 5 times

When a Sony TV flashes five times, that means that there is an AKB circuit fault.
This means that there is something wrong with the video.
When you get this error, several IC and components concerning the video signal must be tested and eventually replaced.
0helpful
1answer

Powers on then right back of light flashes 8 times

i have a sony wide screen projection tv KP-51WS500 Red stand by light on flashs no picture
Not finding what you are looking for?
Sony KP-51HW40 51" Rear Projection Television Logo

111 views

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76791 Answers

Ekse

Level 3 Expert

13435 Answers

Nasir Muhammad
Nasir Muhammad

Level 2 Expert

252 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...