Question about Frigidaire Affinity ATF7000ES Front Load Washer

1 Answer

Keeps pausing pause keeps flashing and machne stops.wont spin out

Posted by Anonymous on

Ad

1 Answer

Frigidaire

  • Official Brand Answer
  • 2,267 Answers

Hello Friend, this is Z. Thank you for your post!

If you are receiving an error code PAUSE, it commonly indicates that the door of your washer is not securely latched or the cycle has been interrupted. Try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume cycle. If these basic troubleshooting tips prove ineffective, try reprogramming your appliance by unplugging it or flipping the household circuit breaker off. It is best to wait approximately ten minutes and then turn on your washer. If the issue persists, then your washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts.

Posted on Jul 22, 2014

Ad

5 Related Answers

katie1971

  • 1 Answer

SOURCE: Won't Star keeps flashing Pause and Err

that was just happening a few seconds ago with mine and i just tried pusing the control button and the options button at the same time for a few seconds... i reopened the door and pressed start again...it's running now... good luck

Posted on Apr 21, 2008

Ad

Jim Wirth

  • 100 Answers

SOURCE: keep stopping pausing

If you leave the machine to itself, will it go through the whole wash satisfactorily? If it does, then the start and stop is designed into it. What it is doing is stopping and reversing the washing action. That is so the clothes will not wind up in a long rope shape, like the winding up of a towel like you use to do to a towel to snap your bother or sister in the showers or at the pool. It UNWINDS the load... It goes a few turns one way, then pauses, then a few turns the other way and pauses. Hope this helps..... 2529817.gif

Posted on Dec 01, 2009

Anonymous

  • 1 Answer

SOURCE: Our frigidaire front loading washer keeps pausing

Same for us,,,
We have to turn the dial and try to put it back approximately at the same place on the dial
(turning clokwise 360 degrees)
Sorry this is the best solution I could find

Posted on Jul 14, 2010

goggomobil

  • 273 Answers

SOURCE: after normal wash and rinse cycle machine goes

Here's something to read:

http://getsatisfaction.com/frigidaire/topics/why_wont_my_frigidaire_affinity_washer_spin

Good luck.

Posted on Mar 09, 2011

DanL

  • 1 Answer

SOURCE: Error / Pause Affinity ATF7000

I had the issue with my Affinity ATF7000 washer displaying err pause err pause .... clicking any button would give me 3 beeps and lights would flash but would get no real error message. Repair man wanted to replace entire computer for $250 plus service call rate. So by dumb luck I did this and got it working.


1. Unplug washer

2. Take off top (screws on back)

3. Unplug connector to the pressure sensor (carefully). Looking at the washer it is mounted to the right side near the front and looks round when looking at it from the top.

4. Plug in the washer and it should display E31. E31 is just saying it cannot communicate with the pressure sensor (which makes sense because you unplugged it).

5. Unplug washer and reconnect pressure sensor.

6. Put top back on and plug in washer.

7. Washer should work but E31 error will remain in memory so if you do call a repair man he may think the pressure sensor needs to be replaced. There is a way to clear error codes but I could not get it to work.


This is my theory on why it worked. The computer program on the washer is stuck in a loop that will not allow the washer to function. When we unplug the pressure sensor we give it a real error and it exits the loop it is stuck in. I am a programmer by day so this may not make sense to some.

Posted on Feb 23, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Zanussi Essential 1400 ZWF14070W1


Check the belt that spins the drum for proper tension. If it has stretched you will have a hassle. Often you can loosen a belt pulley and put some extra tension on belt, restore friction and operation till belt is replaced with a nice, new tight one.

Nov 23, 2013 | Washing Machines

1 Answer

Keeps pausing


What is the model number of your unit?

Feb 03, 2013 | Whirlpool Washing Machines

1 Answer

My washer won't start, it keeps flashing ERR and then the wash-time, and then LOC. My roommate says to fix it before, he held down three buttons, but can't remember which ones. Any idea?


Try the following two buttons: press Options and Select together for 10 seconds (or until the LOC disappears). The pair of buttons held for 10 seconds also sets this control lock.

To find out the error code, turn the Program knob to the start position, Spin Only. Press Start/Pause to start the cycle. Press Cancel to stop the cycle and turn off the LEDs. Press Cancel again and within 5 seconds press and hold the Options and Start/Pause buttons until the LEDs start chasing. Then release the buttons. Turn the Program knob seven clicks clockwise from the Start position. The control will signal the last error code. To clear the error, press and hold Options and Start/Pause for 3 seconds. Then either unplug the washer for 5-8 seconds before plugging it back in. Alternatively, press and hold Options and Start/Pause together for a few seconds until the Wash LEDs appear.

http://www.applianceblog.com/mainforums/frigidaire-electrolux/12950-frigidaire-atf6000es1-wont-drain.html has a link to the service manual for the listed washer (the link is half-way down the page).

I hope this helps.

Cindy Wells

Oct 12, 2010 | Frigidaire ATF6000ES Front Load Washer

3 Answers

I have a golden companion scooter and it wont move it flashes a green light but i haave no info on where to obtain the trouble codes


The L.E.D. located on the tiller
dashboard will indicate with flash codes what problem is occurring.
L.E.D. Flashes 1 time and pauses, 1 time and pauses…. Batteries are low,
scooter will still operate.
L.E.D. Flashes 2 times and pauses, 2 times and pauses…. Batteries are very
low, scooter will not operate.
L.E.D. Flashes 3 times and pauses, 3 times and pauses….Over voltage to
controller.
L.E.D. Flashes 5 times and pauses, 5 times and pauses….Brake is in the
freewheel position or connection to brake is open.
L.E.D. Flashes 6 times and pauses, 6 times and pauses….Paddle or speed
potentiometer problem.
L.E.D. Flashes 7 times and pauses, 7 times and pauses….Paddle or speed
potentiometer problem.
L.E.D. Flashes 8 times and pauses, 8 times and pauses….Motor
disconnected or faulty.
L.E.D. Flashes 9 times and pauses, 9 times and pause….Controller fault.

I hope this helps they are pretty standard codes I got this from Golden Tech Web Site

Aug 17, 2010 | Golden Technologies Golden CompanioN II -...

3 Answers

Panasonic pt47wx52cf tv shut off and wont turn


Please count red light flashes and let me know. There would be long pause between flashes so count pause to pause. It is an error code of TV problem.

May 18, 2009 | Panasonic Televison & Video

1 Answer

F-20 fault


be sure pump is cleaned out

Oct 22, 2008 | Kenmore Elite 45986 Front Load Washer

2 Answers

GE Adora front load washer overloaded now won't start


Washers - Resetting Electronic Controls on a Washer

If there is a pause in the washer cycle, the controls will lock up. The pause can occur because of a power failure or it was put in the test mode at the factory.

Also, if the washer was stopped before the cycle was complete or the consumer has pushed the stop/pause button to temporarily stop the cycle and the cycle is not reset. Over a period of 24 hours, the washer will pump out and spin, but will stay in the final spin.

To correct the situation, shut off the circuit breaker for 30 seconds or unplug the washer, then turn the timer knob around and back to any position other than final spin. Verify the water is turned on and restore power. This should resolve the issue.

Apr 23, 2008 | GE WSXH208A Front Load Washer

1 Answer

Machne beeps and all indicator lamps on right hand column flash


Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped.

Jan 06, 2008 | Frigidaire FTF2140E 3.5 Cu. Ft. Front...

Not finding what you are looking for?
Washing Machines Logo

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6197 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...