Question about Pyramid 906VL Car Audio Amplifier

2 Answers

Pyramid SE301-VL amp wiring confusion...

I have a Pyramid SE301-VL 150 watt amplifier here, but I forgot to tag the wires when I removed it from the houseboat it was installed in... Trying to install it in my boat, but not sure of the wiring on it...

Wire colors are as follows:
1 black, appears to be ground connection
1 red, assuming batt + connection
1 grey
1 green
another black which has splitter on the end ???

Brown, brown/white
Blue, blue/white
Green, green/white
Grey, grey/white

Was connected to Motorolla professional series cassette deck, I intend to connect it to a Kenwood cassette deck on a 4 speaker system.

Any help/information you could provide would be greatly appreciated.
Thanks for your time.

Posted by Bill on


2 Answers


  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer


Red - should be fused & is the +12Vdc system supply voltage.
Chassis = System ground.
Individual Green, Grey, & cooresponding blacks will be the right & left chan Audio ins (Black = neg).
Paired bl/blwh, br/brwh, grey/grwh, & green/grwh will be the audio outs.

Hope this helps !!!!

Dale EE

Posted on Sep 12, 2008



Can imake it rca

Posted on Aug 04, 2008


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I've bought a pyramid crystal 1000 watt 2 channel amplifier used it states it runs at 4 ohms can I run it at 2 or 1 ohms and if so what will the wattage be?

Not to disappoint you too much, but the 1000 watts advertised is just marketing hype. If your amp is the PB781X, it should have only a single 15A fuse on it. Your battery provides 12.5 volts when the engine is off, so at most, your amp draws 187.5 watts of power. Draws, not outputs. No amp is 100% efficient due to heat. When your engine is running, assuming your alternator outputs 14.4 volts, your amp's maximum power draw is about 216 watts. Again, this is what your amp draws, not what it puts out. What you should focus on is the RMS (continuous) output, not Max or PMPO. Those numbers are useless, unfortunately.
Your amp is rated to output 50 watts per channel at 4 Ohms, and 75 watts per channel at 2 ohms. This is when wiring your channels separately, not bridged. I did not see true power specs for your amp while bridged, but it's possible you'll just get the full 150 watts to the single bridged output. Do not attempt to apply a 1 ohm load to your amplifier, as you will run the risk of damaging it. It's not designed to handle a 1 ohm load. If you're lucky, you'll blow a fuse before the amp is damaged, but either way, there is nothing to be gained by attempting it.

If you need further help, I’m available over the phone at

Sep 12, 2017 | Pyramid Car Audio & Video

1 Answer

What is considerd,a chassis ground ?

chissis ground is just simply the car body metal, not metal that moves like car seat. drill a hole smaller than your screw and the drive the screw into it with a lug connected to your wiring

Oct 12, 2014 | Pyramid Car Audio & Video

1 Answer

Installing a model# SE301-VL.

Recommend contacting a local car audio professional or Pyramid customer support directly here:


Oct 12, 2014 | Pyramid Car Audio & Video

1 Answer

Pyramid 7band equalizer 200watt amp model#402-vl how to huck up the wires

Did you say "huck" up the wires?
Recommend contacting a local car audio professional or Pyramid customer support directly here:


Mar 07, 2012 | Pyramid Car Audio & Video

1 Answer

Need advice on setting up amp with my two speakers.

This is hard to explain and what needs to be done is wire in parallel both subwoofers. This website will help just put in the amount of speakers and amount of ohms each and it gives you diagram.

Mar 24, 2010 | Pyramid ZPA150 Car Amp

2 Answers

I have a 300 watt amp, but i just bought 12 gauge wire why wont it allow sound to come from my 12'' sub

There is no reason even if the wire was to small it would still allow ssound.make sure you have good connections.

Nov 08, 2009 | Pyramid 906 300 Watts (peak) 10 Band...

1 Answer

Can i use a 150watt wireing harness with a 20 amp fuse for this model?

Depends on the wattage of the amp, if the amp is 150 watts then yes use a 150 watt amp kit, but i'd go with a 30 amp fuse. Basically just buy an amp kit rated at the wattage of the amp, my preferred brand is street wire, but if you're on a budget buy Scosche. Good Luck, if you have any more questions please ask...

Sep 22, 2009 | Power Acoustik Gothic Series 2-Channel...

1 Answer

Color code for speaker out on a JVC KS R140 car casette player

White - left front
Grey - right front
Green - left rear
Purple - right rear
Yellow - memory power
Blue - remote power (power ant, amp or eq power)

Mar 20, 2009 | JVC KS-F150 Cassette Player

Not finding what you are looking for?
Pyramid 906VL Car Audio Amplifier Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pyramid Car Audio & Video Experts

Alphanso Tee

Level 2 Expert

169 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14841 Answers

Tom Chichester

Level 3 Expert

55667 Answers

Are you a Pyramid Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides