Question about KitchenAid KGST307 Gas Kitchen Range

Open Question

How do I fix the control panel for my 13 year old gas range that has been beeping randomly for over a year?

My gas range beeps, turns oven light off and on, changes clock, shows random oven temp, beeps more in humidity and once turned the oven off while baking.

Posted by Anonymous on

Ad

5 Related Answers

SolutionGuy

Tracy Farrell

  • 331 Answers

SOURCE: Controls lost mind -- keeps asking for probe temp

Houston, we have a problem... Your electronic relay control, (ERC), is shot, kaput, no bueno and must be replaced in order to correct your situation. The ERC part number is 3191106, and retails for ~305.00 dollars! (I kid you not). I guess now is the time you might consider replacement over repair. That's a good question. If you choose to proceed with the repair, repost and I'll help with details on how to do it.

Posted on Aug 11, 2007

Ad

papavic

  • 1 Answer

SOURCE: 8 year old kitchenaid gas range nom fire in the oven

I went to the kitchenaid web site for parts and found a trouble shooting section. I read about how a electronic glow coil works and discovered that mine was just old and did not reach the right voltage to open the gas flow valve.

Posted on Feb 21, 2008

Ad

Anonymous

SOURCE: constant beep

http://www.applianceblog.com/mainforums/showthread.php?t=3537

Posted on Mar 15, 2008

Anonymous

  • 1 Answer

SOURCE: KitchenAid gas range superba not reaching/registering right temp.

kitchenaid superba electric double oven "takes too long to heat up"

Posted on Dec 06, 2009

Anonymous

  • 1 Answer

SOURCE: probe indicator beeping. Can't turn off.

there is a continuous beep on my oven and it says enter the probe temperature. I never used and would like to cancel...how?

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do turn on oven


Good Afternoon Friend,

I understand you want to know how to turn on your Frigidaire range, model# FGF378AC. First, you will need to make sure you have set the clock, by pressing the clock button and then pressing and holding down either the up or down arrows until the correct time displays.

Secondly, you will turn your oven on by pressing the "Bake" button and then pressing and holding down either the up or down arrows until the correct temperature displays. Once you release the up or down arrow, your oven should begin heating to the desired temperature. The control will beep three times, once the temperature has been reached.

I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 29, 2014 | Frigidaire FGF378AC Gas Kitchen Range

1 Answer

The oven will pre heat to set temp, then when it reaches temp the oven beeps and both oven elements turn off. At this point the control panel (clock LED) shows an F2 error.


Good afternoon.
F2 for hotpoint means oven temp sensor thinks oven exceeded 650 degrees .Did that happen?
Probably not so have your sensor checked or replaced. It should be a probe device in oven back wall.


Was this helpful?

Aug 16, 2011 | Hotpoint RB787 Electric Kitchen Range

1 Answer

Whirlpool electric range timer constantly beeps and displays E2-F3 I don't even use the oven I just want beeping to stop I press STOP which changes display back to clock, but soon it returns to E2-F3...


Hi

Thanks for using FixYa.
Error F3-E2 in your Whirlpool oven means oven too hot and to resolve this issue you'll have to replace the oven temp. sensor (probe). Please rate the solution if the issue is resolved or post a comment for further assistance.

Thanks

Rylee

Oct 06, 2010 | Whirlpool GS475LEKS Gas Kitchen Range

1 Answer

I have a tappan range that keeps getting F1/F3 in on the display panel.


How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
  1. Disconnect power to stove
  2. Gain access to the back of the clock (electronic range control or ERC).
  3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  4. Make sure everything is clear and will not short out when power is turned back on.
  5. Turn power back on to stove.
  6. Watch for the F1 and listen for the beep.
  7. If you get the F1 and beep, replace the ERC.
  8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
    NOTE: Some models incorporate the touch pad and the clock as one part. * We have seen a few of the newer Maytag ranges with a F1 fault code and the problem was the oven temp sensor, check carefully the wires to and from the oven temp sensor!!

Mar 03, 2010 | Tappan TGF363 Gas Kitchen Range

1 Answer

I have a Maytag model MER5775QAW free standing range. When you press "bake" and then set the temp. and press "bake" again the numbers instantly climb to the set temp and the buzzer beeps showing oven at...


Unplug the range open the control panel to access the electronic oven control. Unplug the wires and wait 5 minutes. Replace all wires on the control and turn the power back on.
If this does not reset your oven control it must be replaced.
Your ERC(clock) is bad and must be replaced.

Nov 09, 2009 | Maytag MER5775Q Electric Kitchen Range

1 Answer

Purchased at Maytag Gemini MER6770 in 2000. It


Sounds like the cancel (or stop) button is making contact by itself. Clock (oven control board) may need replacement.
One option to buy it new, your part number is 12001661
Coupon "New10" chops 10% off.
Another is to send the clock to be rebuilt. Google "stove timer rebuild", you'll find plenty of companies which can repair your original clock. In case you need it, the original part number is 74004542.
To get to the clock, remove the back of the control panel. Good luck.

Oct 24, 2009 | Maytag MER6772 Gemini Electric Kitchen...

2 Answers

GE true temp oven f2


This happens every time I clean my oven. It overheats, shows the f2 light and BEEPS loudly. The only way to stop it is to turn the oven off at the breaker box, wait until it cools (usually 2-3 hours), flip the breaker back on and start the process all over again until the unit is clean. If it's not to dirty, sometimes it's easier to juat use Easy Off.
hope it helped

Jan 09, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...

2 Answers

Whirlpool gs475lems range oven problems


my oven was converted to LP gas we move overseas.It worked for about a year then all of a sudden the oven stopped working. The burners work perfectly but the oven just keeps clicking after preheat is finished. We replaced the upper electronics board so what could it be now

Dec 02, 2007 | Whirlpool GS475LEKS Gas Kitchen Range

Not finding what you are looking for?
KitchenAid KGST307 Gas Kitchen Range Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Kitchen Ranges Experts

Jay B

Level 1 Expert

19 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

ittco

Level 1 Expert

13 Answers

Are you a KitchenAid Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...