Question about Minolta bizhub 180 Black and White Copier

1 Answer

Konica Minolta bizhub 164 m2 - Minolta bizhub 180 Black and White Copier

Posted by Hamad Ahmed on

Ad

1 Answer

Tareq Bin Mostaq Mostaq

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Minolta Master
  • 1,449 Answers

Press the Utility button,
then Stop 0 0 Stop 0 1

then scroll to Clear Data, and then Supplies Data and clear.

You must be aware that clearing this counter clears the drum, developer and other counters.

Which are very important for copy quality, and not replacing them may cause more harm than good.

Posted on Jul 17, 2014

Ad

5 Related Answers

mochicas

  • 26 Answers

SOURCE: Driver utility of Konika Minolta Bizhub 162

Use the bizhub 180 same family

driver

Posted on Feb 21, 2009

Ad

Anonymous

  • 210 Answers

SOURCE: Bizhub Konica Minolta - Error Code C1183

First check the alignment front and rear of the finisher, check the finisher exit guide rollers if the paper is exiting properly, open both rear and the front cover and check the lower gears attach is the up/down drive belt. that lower gear one might be broken by the pin slot.

Posted on Jul 09, 2009

SOURCE: ERROR C0910 KONICA MINOLTA BIZHUB DI 2010

2nd Drawer Lift-Up Motor Failure - The Lift-Up Sensor is not unblocked even after the set period of time has elapsed after the paper liftup operation for the drawer has begun.

Reset your Toners and Imaging units for Bizhub and CF series.
http://www.chipreset.eu

Posted on Nov 27, 2009

firecontrol7

Norman J Weimar Jr

  • 6960 Answers

SOURCE: konica minolta bizhub 350 error code c5352

Cooling Fan fault. To clear open and closer the front door.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Posted on Apr 04, 2010

Anonymous

  • 1110 Answers

SOURCE: kONICA MINOLTA BIZHUB 750 SHOWING C3803 ERROR

You have a problem with the fusing unit. This is the assembly that gets hot and "fuses" the toner onto your paper. This error code means that the fusing unit did not warm up properly. You will need to have a service company come out to diagnose and repair the problem then reset this code as service mode entry is required in order to reset. It could be as simple as cleaning the thermistor, replacing the thermistor, thermal fuse etc. I would estimate the cost at around $200.00.
Here is the section from the service manual that deals with this code:
Thermistor /1 (TH1) detects a low
temperature when a specified
period of time elapses after the
fusing heater lamp is turned ON
for the fusing ON control.

Posted on Jun 09, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Konica minolta bizhub 164 showing M2 maintanaince call

You need to replace 1st the consumables before simulation/reset to prevent further damage to Bizhub 164.
0helpful
1answer

BIZHUB 164 error M2 what have I to do

Replace the developer and the drum make sure counters are cleared first and that Gradation adj is run along with Toner adj

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

BIZHUB 164 error M2 what have I to do

replace the drum and developer and then reset the counter

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

Konica mintola bizhub 164 maintainace call (M2)

replace the drum and developer and clear the counter also ensure you run the F8 after developer been replaced and new drum are installed

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

Maintainace call (M2)

Enter in the service mode and select Counter mode and clear the mnaitenace counter and PM counter.
3helpful
1answer

Konica bizhub 164 M2

1-Press "Menu
2-press Quick settings,
3-then press right arrow key 2 times
4-press Quick settings
5-then press left arrow then right arrow key.
0helpful
1answer

Konica minolta bizhub 164 reset code m2

Utility button then stop 00 stop 01. use arrows to get to clear data. then to maintenance counter clear/yes

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

17helpful
2answers

Desbloqueo del codigo m2 en konica minolta bizhub 163

Este código significa que la vida las partes de su desarrollo + unidad de imagen se ha caducado. Ahora es el momento de reemplazar las partes.
Not finding what you are looking for?
Minolta bizhub 180 Black and White Copier Logo

208 views

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Ekse

Level 3 Expert

13435 Answers

Brad Brown

Level 3 Expert

18733 Answers

George Mclaughlin

Level 2 Expert

370 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...