Just no power. outlet is ok! reset button does nothing to help

Resolution:If the washer does not accept inputs from the control panel, follow the Hard Reset steps below to reset the control:

Unplug or turn the circuit breaker off for 30 seconds.

Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.

Press the Pause / Cancel / Stop button twice to clear the display.

Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.

Note: If the Hard Reset does not work, there may be an internal failure with the washer, that requires service.

Sometimes routers can die periodically.
You can perform a 'reset' on the router to put it back to factory settings, but you will lose everything you have configured.

To reset, press(and hold) the reset button on the back of the router (its small).
Continue to hold it for 30 seconds
Unplug the power (while still holding the reset button).
Wait 30 seconds, then plug it in again.
(Don't let go of the reset button just yet)
Wait 30 seconds after plugging it in, then let go.
Go make a coffee or do something for 5 minutes while the router does its thing.
If all goes well you'll be back at square one.

you either have a faulty power supply or faulty main board. Vizio power supplies on the older sets are pretty decent. It's usually the main boards that go. These older main boards tend to be pricey so it may be better to buy a new set.

General Linksys has a reset button on the back on the unit. Its really small and recessed into the unit. To cause the reset to happen do the following:

1 Get a pen/paperclip something small and pointy and hold down the reset button
2 after 20-30 seconds of holding button down you will notice a change in the lights in the front once you see this unplug the unit and wait 5 seconds.
3 Plug unit back in and you should be good to go

On some units if you enter into a web browser 192.168.1.1 you can enter into the admin controls and do a restore to factory defaults and worse case if you need to you can flash the unit (this will also update the system to its latest firmware)

perform power cycle
1. Unplug the unit’s power cord from the back of the printer while the printer is 'on'.
2. Hold down the ‘On’ button for 60 seconds
3. Plug the power cord back to the unit while holding the ‘On‘ button down.
4. This will reset the printer’s mechanical systems and discharge all capacitors.
If the issue still persists, then

1. Unplug the power cord from the wall outlet.
2. Unplug the power cord from the all-in-one.
3. Wait 30 seconds, and plug the power cord back into the wall outlet.
4. Press and hold the # and 6 buttons on the numeric keypad.
5. While still holding the buttons, plug the power cord back in to the all-in-one. Continue to hold the buttons for two seconds, and then release them.

This should resolve your issue.

Can't get t v on

Hi

If you find the lights flashing, we could try resetting the printer.I have explained the reset procedures below

POWER DRAIN:-Turn off the printer, Unplug the power cable from printer and from the wall outlet.Press and hold ON buton for 30-60 seconds.


PARTIAL RESET:-Unplug the printer power cable while its ON, press and hold # and 3 button and connect the Power cord while holding.Wait untill the ON light flashes, then release the buttons.

----(for below reset cartridges must be removed out)---------

SEMI_FULL RESET:-Remove the ink cartridges, Unplug the printer power cable while its ON, press and hold # and 6 button and connect the Power cord while holding.Wait untill the ON light flashes,or wait for 20 seconds,hen release the button.If the printer goes off dont worry release the button and Push the ON button.


FULL NVM RESET:-Take the Ink Cartridges out, Unplug the printer power cable while its ON, press and hold OK and CANCEL button and connect the Power cord while holding the buttons.keep Holding the buttons until the printer goes off ,release the button and Push the ON button.

Thanks
Riz

Find and replace the following caps, Ec18, 19, 20 / 1000uf/16v,
Ec9, 10 / 1000uf/35v, Ec14, 25 / 470uf/35v should resolve the problem. You can get the caps at almost any electronics supply.
This is a common problem in this unit.
Good Luck!
Happy Thanksgiving!
Bill

William Rayburn, CET
Premium Technologies
PO Box 442
Long Beach, WA. 98631
360-642-4993
[email protected]

The only solution at this point would be to get the power supply repair since new boards are not longer being manufactured. In about 95% of the time if the LCD doesn't power up or turns OFF by itself or need to be unplug for some time to make work again; those are the symptoms of a dying or defective power supply.
I service these power supplies, for more info write to [email protected]

Bad Convergence circuit , replace 2 STK392-110 & fuse will take care the problem