Question about Hobart HL600 Legacy Stand Mixer

Open Question

Error code 01, pls, give me solution, what is problem, error code 01?

Posted by Anonymous on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get a manual for a sunbeam vista mixmaster mixer has no model no. does have a service no. 7-01-10D Do you have a manual for this


I google Sunbeam Vista and found this website
www.davesrepair.com/DIYhelp/DIYMixmaster-Model-Number-Locations.htm

Jan 07, 2017 | Sunbeam Food Mixers

1 Answer

What is the error code b-in


It's meant to tell the operator that the bowl is not in proper operating position. If the bowl is in the proper position then the bowl in switch may be bad.

Jul 01, 2015 | Hobart HL600 Legacy Stand Mixer

1 Answer

Where do I drain the oil in a 60qt. thunderbird mixer


If you are referring to the transmission, I believe it's a sealed unit.

  • 3-Speed gear box
  • Transmission: Wide-faced, hardened alloy steel, helical gears fully sealed in transmission lubricant with heavy-duty ball bearings and clutch combine for highly dependable, quiet operation.
  • Jun 12, 2014 | Thunderbird ARM-01 Planetary Mixer

    1 Answer

    Oven wouldn't turn on, screen said F2E1


    If you have a KitchenAid range, the F2 E1 code indicates a keypad problem. If it recurs and continues to give the error after you press Cancel, then you will address the issue. The cake pan position has very little to do with the error.

    The fix could be as simple as finding a damaged conductor in the wiring harness and using a conductive silver pen (or use the rear window defrost repair kit liquid applied with a needle and not a wide brush) to repair the break. On some ranges you might need to replace the keypad. Other models have the keypad integrated into the ERC (clock and entire control panel).

    I hope this helps.

    Cindy Wells

    Dec 03, 2012 | KitchenAid Food Mixers

    1 Answer

    Need manual for Sunbeam Vista Mixmaster 70110D


    How do i Take rear speed control nobe off on a sunbeam mixer 7-01-10D need to control the speed of the mixer

    Oct 28, 2011 | Food Mixers

    1 Answer

    What is error code 99 for a hobart HL 600 mixer?


    error 99 stands for communication fault between timer board and the sr drive.there are 5 things that can cause this error.1.rs-485 cable disconnected or malfunction 2.1 con monitordisconnected or malfunction. 3.run/stop wiring disconnected or malfunction. 4.timer board malfunction. 5.sr drive malfunction. hope this helps, dont forget to vote, thanks, monomoy

    Jan 29, 2010 | Hobart HL600 Legacy Stand Mixer

    1 Answer

    Noisy, high pitched whirring MUM6622UC/01 Bosch Universal Mixer


    My wife's bosch mixer had a similar problem but it was a very loud grating problem. I talked to the bosch dealer in Utah, sorry, I've forgotten which one-- the one that does the repair. This is typically what happens: the seal on the blender wears out, which results in fluids from the blender dripping into the motor, onto the upper motor bearing. So, the upper bearing corrodes and is what is causing the bearing failure and the loud noise (needed hearing protection to operate it). I was lamenting the cost and time it would take to ship the mixer both directions (not actually that much compared to the price of the mixer), and he said he would sell me the bearing and the bottom replacement part of the blender that was leaking. So, I did the repair myself, but it took awhile, and I had to build a puller for the bearing to get it off the shaft, modifying a harbor freight gear puller. But it now is back to new. So, it was a success for me, but i would recommend anyone who isn't very mechanical to just send it off to Utah (again, I forgot the place, I think they talk about the shop in one of the other posts), and you will have a better than new machine.

    Nov 08, 2009 | Bosch 700 Watts MUM6622 Universal Series...

    2 Answers

    Motor is burned out


    Are you sure the motor is bad?

    Dec 03, 2008 | Hobart H600 Stand Mixer

    1 Answer

    Hobart hl600 mixer


    I know what these codes are: code 19 is that phase c is over current fault and code 23 is a motor stall fault.I would start by making sure you 3 phase wiring going into the mixer is there.I service these mixers as im a service tech for hobart.these units are very detailed and i can walk you thru some things to check but if you have an electrical problem you most likley will have to call a hobart service tech because we have special equipment to diagnose the fault.let me know it may be something simple as these mixers are usally maintenance free.

    Nov 14, 2007 | Hobart HL600 Legacy Stand Mixer

    Not finding what you are looking for?
    Hobart HL600 Legacy Stand Mixer Logo

    Related Topics:

    125 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hobart Food Mixers Experts

    Pieter Vleeshouwers
    Pieter Vleeshouwers

    Level 3 Expert

    2027 Answers

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Lawrence Oravetz

    Level 3 Expert

    10548 Answers

    Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...