Canon MultiPASS MP390 All-In-One InkJet Printer Logo

Related Topics:

Question about Canon MultiPASS MP390 All-In-One InkJet Printer

Open Question

Where can i download Repair manual for a canon i9950 printer?

Posted by Anonymous on

Ad

5 Related Answers

budhoyo

UD SETYA ELCOM

  • 26 Answers

SOURCE: Canon i9950: Full waste ink absorber

Dhedik maybe this action can solved your problem Reset Waste Ink Counter printer Canon i9950 :  1. power off  Printer 
2. Push and hold resume  button and push power button 
3. Hold  Power button and release Resume  button 
4. Push Resume button twice ( 2x ), and now release resume button and power button 
5. Green light will blinking and  stop.
6. When green light on, push resume button 4 x 
7. Push  Power button and printer will off, if that isn't off, push power butto again until print off position.

ok good try, don't forger to vote me, Fixya  

Posted on Nov 03, 2008

Ad

Anonymous

  • 4 Answers

SOURCE: service manual vanon i9950

1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power
button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power
button.)
3) While holding the Power button, press the Resume/Cancel button 2 times, and then release the Power
and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights
alternately in orange and green, starting with orange.)
4) When the LED lights in green, press the Resume/Cancel button the specified number of time(s)
according to the function listed in the table below. (Each time the Resume/Cancel button is pressed,
the LED lights alternately in either orange or green, starting with orange.)
5) After the function (menu) is selected, press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu
selection mode automatically.)
Time(s) LED
Function
Remarks
0 times Green Power off When the print head is not installed, the carriage
returns and locks in the home position.
1 time Orange Service test print See Section 3.5 Verification Items, (1) Service test
print.
2 times Green EEPROM information print See Section 3.5 Verification Items, (2) EEPROM
information print.
3 times Orange EEPROM initialization
4 times Green Waste ink counter resetting
5 times Orange Destination settings After performing step 5), and follow the Destination
settings procedures.
6 times Green Print head deep cleaning
7 times Orange Media sensor correction After performing step 5), and follow the Media sensor
correction procedures.
8 times Green CD-R test print Not used in servicing
9 times Orange CD-R print position
correction (horizontal)
Not used in servicing
10 times Green CD-R print position
correction (vertical)
Not used in servicing
11 times
or more
Return to the menu selection

For full Service manual I've uploaded it here:
http://www.megaupload.com/?d=BLC9L7OU

Posted on Mar 26, 2009

Ad

Anonymous

  • 4 Answers

SOURCE: i9950 Canon printer with message 'Waste ink absorber almost full.

1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power
button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power
button.)
3) While holding the Power button, press the Resume/Cancel button 2 times, and then release the Power
and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights
alternately in orange and green, starting with orange.)
4) 4) When the LED lights in green, press the Resume/Cancel button 4 times to reset 'Waste ink absorber'.
5) Press the Power button to execute.

Posted on Mar 26, 2009

Anonymous

  • 1 Answer

SOURCE: repair manual for a canon mp 390 printer

Change the cartridge message. I changed both black & color but still the same message would appear. I can NOT make any maintenance ( cleaning the nozzle,....)

Posted on Sep 06, 2009

muntejaya

Muntejaya Ginting

  • 10422 Answers

SOURCE: I have downloaded the recommended

Hi, please get new driver here: www.driversdown.com/
www.nodevice.com/driver/company/Canon/Printer.html
www.usa.canon.com/cusa/office/products/.../hs_1200ts

Jay ghtb

Posted on Feb 12, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to clean out the ink bin on canon i9950 please

follow my link below to another fixya solution that may resolve your problem also, as it lists waste ink reset instruction for many canon printers there.

waste ink reset instructions
0helpful
1answer

I can't print with cannon i9950 in windows 7

Canon i9950 Printer -windows 7 Driver Problems
But the October 25, 2009 driver for 64-bit Windows 7 is at http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDetailTabAct&fcategoryid=331&modelid=9870

Did you look for this at Canon?
3helpful
1answer

Canon i9950 printer problem error 5c00

According to the Service Manual Error Code List these are the two possible candidates to cause this failure:
- Purge unit (Part-No. QM2-1307)
- Logic board ***’y (Part-No. QM2-1272/QM2-1273)
which means, this device has to go to the service.
(Or to bereplaced)
Best Regards
cominarosa
1helpful
1answer

Canon i9950 will not print with windows 7, The printer is on a company network and can be seen but will not print the test page.

try the following driver from canon site, it should work with windows 7:
http://software.canon-europe.com/software/0035868_0010043.asp?model=
download the file and open it. after installing the file, you should restart the copmuter and see if it works for you
0helpful
1answer

Canon i9950 colour deterioration

You can try changing cartridge but that would help little since the print head on canon printers are on the printer itself. Although you can give it a shot first since that would definitely be the cheaper option.
13helpful
4answers

Canon i9950: Full waste ink absorber

Dhedik maybe this action can solved your problem Reset Waste Ink Counter printer Canon i9950 :  1. power off  Printer 
2. Push and hold resume  button and push power button 
3. Hold  Power button and release Resume  button 
4. Push Resume button twice ( 2x ), and now release resume button and power button 
5. Green light will blinking and  stop.
6. When green light on, push resume button 4 x 
7. Push  Power button and printer will off, if that isn't off, push power butto again until print off position.

ok good try, don't forger to vote me, Fixya  
0helpful
1answer

I9950

sure...on the front panel, under menu, you can select that function. The manual will walk you through it. That's pretty standard on most good printers, these days, and I always do that when working on printers.

Got Backup?
3helpful
4answers

Canon i9950

Seems impossible to reset the counter, is there a way to manually reset?
6helpful
4answers

Service manual vanon i9950

1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power
button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power
button.)
3) While holding the Power button, press the Resume/Cancel button 2 times, and then release the Power
and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights
alternately in orange and green, starting with orange.)
4) When the LED lights in green, press the Resume/Cancel button the specified number of time(s)
according to the function listed in the table below. (Each time the Resume/Cancel button is pressed,
the LED lights alternately in either orange or green, starting with orange.)
5) After the function (menu) is selected, press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu
selection mode automatically.)
Time(s) LED
Function
Remarks
0 times Green Power off When the print head is not installed, the carriage
returns and locks in the home position.
1 time Orange Service test print See Section 3.5 Verification Items, (1) Service test
print.
2 times Green EEPROM information print See Section 3.5 Verification Items, (2) EEPROM
information print.
3 times Orange EEPROM initialization
4 times Green Waste ink counter resetting
5 times Orange Destination settings After performing step 5), and follow the Destination
settings procedures.
6 times Green Print head deep cleaning
7 times Orange Media sensor correction After performing step 5), and follow the Media sensor
correction procedures.
8 times Green CD-R test print Not used in servicing
9 times Orange CD-R print position
correction (horizontal)
Not used in servicing
10 times Green CD-R print position
correction (vertical)
Not used in servicing
11 times
or more
Return to the menu selection

For full Service manual I've uploaded it here:
http://www.megaupload.com/?d=BLC9L7OU
Not finding what you are looking for?

56 views

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4362 Answers

old marine
old marine

Level 3 Expert

2417 Answers

Cindy Wells

Level 3 Expert

6583 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...