Question about Onkyo TX-DS575 Receiver

Open Question

OnkyoTX-DS575schematic diagram i have a problem with my Onkyo TX-DS575 receiver.no power going to the circuit.the input voltage ok and the fuse is ok.but no output no 13vdc.any idea about this problem? i also need schematic diagram for this unit.can you help me pls.thank you

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 752 Answers

SOURCE: Need fiber optic input jack for Onkyo TX-DS575

Had it ever worked, or are you setting it up for the first time?
Have you ASSIGNED the digital input in the menu?

Posted on Dec 18, 2007

Ad

Anonymous

  • 27 Answers

SOURCE: Need help hooking up a KRK powered subwoofer to an Onkyo 7.1 receiver

a single male rca spliting into 2 male rca's ....a signal splitter

Posted on Oct 30, 2008

Ad

Rob Galayda

  • 54 Answers

SOURCE: Onkyo TX-DS575 - intermittent audio

You have a problem that was inherent with all Onkyo receivers from this period. You need to contact Onkyo because the microprocessor needs to be replaced. Last I checked, its about $80 from onkyo.

This is NOT an isolated incident as darn near every Onkyo receiver model had this problem.

Good luck...
Rob

Posted on Nov 15, 2008

Anonymous

  • 458 Answers

SOURCE: onkyo tx-ds575 receiver shuts down when switching

may be speaker or wire have problem

Posted on Oct 28, 2009

Anonymous

  • 118 Answers

SOURCE: Dolby digital output

sounds like you are watching cable.

Posted on Nov 03, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have lost the remote control of my Onkyo TX-DS575 AV reciever/DTS Amp and cannot find one in the market. I have used a universal remote which had a couple of Onkyo codes with it but it doesn't work. Is...

Amazon.com, MyRemoteControls.com, and Remotes.com all sell a replacement remote for the TX-DS575. I have also seen the Onkyo TS-DS575 receiver with remote listed on eBay for as low as $35. Keep looking; the remotes are out there.
0helpful
1answer

How to you change an ac fuse in an onkyo ds575

Remove the top covers after the mains power was disconnected. Now check on the rear panel left corner for the fuses. Remove them and test using a multimeter in the continuity range. replace only with the correct rating and if this blows off the set has a short within and an isolation test will confirm the stage. check with the secondary voltage and check the outputs.
2helpful
1answer

OWNERAS MANUAL TX DS575

You can get the manual on the link below.

http://www.intl.onkyo.com/downloads/manuals/pdf/tx-ds575x_manual_e.pdf

If that is not the right on then go to this link below and click where it says it is free

http://safemanuals.com/user-guide-instructions-owner-manual/ONKYO/TX-DS575-_E


Good Luck and please rate 4 thumbs up for the free answer
2helpful
1answer

Onkyo asv810pro how do you reset microchip

Hi there
To answer your question;
Try holding the video1 input button on the amp while powering the unit.
I`m not sure if its going to work with your model but give it a shot(nothing to lose)
Works on tx-ds serie
If you`d like the service manual leave me your email, it`s 2.7megs in pdf format
Hope this help Happy holidays
1helpful
1answer

Onkyo TX-DS575 - intermittent audio

You have a problem that was inherent with all Onkyo receivers from this period. You need to contact Onkyo because the microprocessor needs to be replaced. Last I checked, its about $80 from onkyo.

This is NOT an isolated incident as darn near every Onkyo receiver model had this problem.

Good luck...
Rob
2helpful
1answer

Will not power up but stand by light is powerd up

I have onkyo tx-ds575 and i need to conect it to my tv and have audio from a LCD flat panel.
1helpful
1answer

Need fiber optic input jack for Onkyo TX-DS575

Had it ever worked, or are you setting it up for the first time?
Have you ASSIGNED the digital input in the menu?
0helpful
1answer

TX-DS575 reciever

Normally you hear a clicking sound coming from the inside when you turn on your amp. That's the sound of the magnetic circuit breaker (switch). If you tap your amp to turn it on, and if the amp gets turned on after you did it:), then I suppose the problem is on the relevant switch.
Not finding what you are looking for?
Onkyo TX-DS575 Receiver Logo

Related Topics:

144 views

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

The Knight
The Knight

Level 3 Expert

76823 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...