When temperature is set for gas oven it makes a clicking sound then it stops and a few minutes starts again on and off continuously

It sounds like you are experiencing an issue with your Viking VGSC486-6Q gas oven where the gas continues to flow and the oven continues to heat even after the desired temperature has been reached. This can be a dangerous issue, as it can cause the oven to overheat and potentially start a fire. Here are a few steps you can try to troubleshoot the issue:

1. Check the oven sensor: The oven sensor is responsible for measuring the temperature inside the oven and sending a signal to the control board to adjust the gas flow and heat as needed. If the sensor is not functioning properly, it can cause the oven to continue heating even after the desired temperature has been reached. You can try cleaning the sensor with a dry cloth and making sure it is securely connected to the control board.
2. Check the control board: The control board is responsible for receiving the signal from the oven sensor and adjusting the gas flow and heat accordingly. If the control board is faulty, it can cause the oven to continue heating even after the desired temperature has been reached. You can try resetting the control board by unplugging the oven and plugging it back in, or you may need to replace the control board.
3. Check the gas valve: The gas valve is responsible for regulating the flow of gas to the oven. If the gas valve is faulty, it can cause the oven to continue heating even after the desired temperature has been reached. You can try cleaning the gas valve and making sure it is securely connected, or you may need to replace the gas valve.

If none of these steps help resolve the issue, it may be necessary to have the oven repaired by a professional. It is important to address this issue as soon as possible, as it can be dangerous to use an oven that continues to heat even after the desired temperature has been reached.

i'm not familiar with your specific unit but ..sounds like an electronic gas value has gone bad or has a bad connection when that happened to my friend it wasn't that expensive to have it fixed .. BYW it acted like this for a while then stopped working completely

This sounds like a bad temperature sensor. It's showing the oven is overheating when it's really not overheating. I would try to replace the temperature sensor and see if that helps!

What make and model? If you can unplug wait 30 seconds and try to hear exactly where the click is, Then get back, i will wait.

What happens in this style ignition system is that the thermostat or electronic control switches power to the oven ignitor and gas valve circuit which are connected in series (one after the other). As power flows through the ignitor it heats and draws current (measured in amperage). Once the oven ignitor draws a specific amount of current the oven valve opens to allow gas to flow to the oven burner where the glowing hot ignitor (glow bar) ignites it. Power must continually flow through the ignitor and oven gas valve for gas to be released into the oven burner to create a flame. Once the set temperature is achieved the control stops all power to the ignition circuit which causes the ignitor to dim and the oven gas valve to close, stopping any burner flame. Cycling on and off continues to maintain the specific temperature the control is set for.

The flame went out.  Move the oven control back to where it sounds like it is lighting.  After it clicks a few times and sounds like you have a flame set your temperature again.

i would have to say that there would be a problem with the ignitor and control regulator

Maytag Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution F0 Function key stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information. F2 Oven temperature too hot Replace relay board, if present, or oven temperature sensor (RTD). Check sensor harness. F3
or
F4 Shorted or open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok. F5 Watchdog and hardware conflict Replace clock (ERC). F7 Function key shorted or stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F8 Analog / Digital problem Replace clock (ERC). F9 Door latch Check door latch components.

that actually sounds to be pretty normal operating procedure unless im not understanding correctly, the unit will shout off, and cycle back on to maintain proper temp as cooks, the" top lef bank of burners" they show signs of clicking??? but not actually igniting correct??? and do they ever start to click when unit is completly off???

i have a whirlpool gas accubake range and only two burners will ignite. The other two burners make a clicking sound and release gas but never light. I have to use a match to light the other two burners and the flame is uneven on one. What should i do?