Question about LG WM-2277HW Front Load Washer

1 Answer

BAD INSTALLATION ON LG 4.00 WM2496H*M TROMM WASHER.!!!!!!!!!!!

DEAR SIR, I JUST PURCHASED a new WASHER and removed old one FRIDGIDARE/ of very poor quality /together with squashed beat up plastic liner.
, Before my installation of a new LG heavy duty washer I bouth again that ugly nasty piece of plastic which supposed to protect my floors agains any leaks.. The liner occures very weak and while the service person was installing the machine it cracked in few points as it was
not designed for such a heavy and oversized washer... Now the washer looks very poor located in that clamsy, cracked standard liner without any dignity!!! ....... and it makes me crazy and I can not make any laundry untill that liner will be removed,
Please note this is very heavy machine and to involve the installation crew it will cost me again.
I do not mind to pay extra but I need to know from expert like you , how properly it should be installed? Do they sell any durable accurate liners for this machine? What do you think about that extra base on the bottom/ for storage, too/ Please contact me as soon as you have time as my laundry is put on hold.!!!I I am waiting with my stackable dryer to put it on the topof this machine. I will wait UNTIL THIS PROBLEM WILL BE SOLVED.
The best regards,Iivona Marona/ TEL 1 202 321 9060

Posted by Ivona on

×

Ad

1 Answer

James Greene

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 240 Answers

The storage bottoms are ok in quality, and do give you more space. They are built for just the use of the washer/dryer they are made for, so they will hold up. Best idea, is when you get your base units, tell the store you want a new pan liner installed as well. You may also want to tell the store that the installation personel who set up your new machine broke the last one and you want some sort of credit, free delivery, new pan liner, discount, etc. All stores (Home Depot, Lowes, Sears, Ace) that carry plumbing products, appliances, etc, will carry a heavy duty floor pan for your unit. Good luck and let me know if you need further information. Jim

Posted on Nov 05, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 olds aurora washer pump or lower tank is leaking. Only info I can find to remove or inspect says remove passenger side wheel well but it's welded and not possible. Please help..


Inner wheel well or fender liner-- is what you pull
back, to get in there

Just plastic push pins & maybe a couple
of screws,then pull the plastic liner clear

Not welded

You can see & get to the top of the tank
to fill it,so you know where it is

Just get access from the wheel well

Best raise & support one side of subframe
& remove the one wheel

Use a screw driver on the two side slots ,in the push pin
heads, to pull them out (not all the way) then remove them

Nov 23, 2014 | 1999 Oldsmobile Aurora

1 Answer

Fridgidare washer front load won't spin & there's water in the tub. It's about 10 years old


If it's that old, you're better off buying a new unit. You'll spend about half the cost of a new one fixing it.

Jun 11, 2012 | Washing Machines

1 Answer

I started to wash some blankets and it will stop, while filling up and gave and F11 code.


Hi, I've had that same problem. The problem is the CCU circuit board inside at the top, back of the machine. There are cold solder joints on the circuit board where the relays and spade connectors are supposed to be soldered to the underside of the board (poor quality control at Whirlpool) You'll need to remove the circuit board and have the spots touched-up. The inputs to the circuitboard housing are keyed but it's still best to tag which wire goes where. You will break a few tabs on the housing when you take it apart (poor plastic choice by Whirlpool) It's best to remove the entire assembly then take the board out when your at the table cursing Whirlpool. If your up for the task great! if not, just print out this response and have a service person do it or take out the whole assembly and let a good appliance repair shop do it, it's up to you. This repair will also take care of an FdL code. Once the board is out the repair takes about 15 minutes. After completing mine the machine hasn't missed a beat in two years. Good Luck.

Dec 02, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Our washer is locked and message is dl, it is a duet . it will not start cycle or unlock


Hi, I've had that same problem. The problem is the CCU circuit board inside at the top, back of the machine. There are cold solder joints on the circuit board where the relays and spade connectors are supposed to be soldered to the underside of the board (poor quality control at Whirlpool) You'll need to remove the circuit board and have the spots touched-up. The inputs to the circuitboard housing are keyed but it's still best to tag which wire goes where. You will break a few tabs on the housing when you take it apart (poor plastic choice by Whirlpool) It's best to remove the entire assembly then take the board out when your at the table cursing Whirlpool. If your up for the task great! if not, just print out this response and have a service person do it or take out the whole assembly and let a good appliance repair shop do it, it's up to you. This repair will also take care of an FdL code. Once the board is out the repair takes about 15 minutes. After completing mine the machine hasn't missed a beat in two years. Good Luck

Nov 30, 2010 | Whirlpool GHW9400 Duet Washer

1 Answer

Where is the windshield washer pump on a 1995 olds Aurora?


It is located under the passenger side front fender. You have to remove the "wheel well" liner to access the pump. It is not a costly item and is carried by NAPA. Getting to it is the work. Jack the car up on right front side---remove wheel and then remove wheel well liner . It involves some phillips head screws along with some plastic fasteners.

Oct 15, 2010 | 1995 Oldsmobile Aurora

1 Answer

My washer dryer 4 years old. Dryer has no heat. Washer will not spin, drum just moves slighly from side to side,


probably a physical problem of your metal lip spinning onto the plastic white rim which probably deteriorated into small plastic pieces you werent aware was your plastic rim liner

Sep 07, 2010 | Whirlpool Washing Machines

1 Answer

How do i change my windshield washer fluid reservoir in my 1999 lexus ls 400


You will need to remove the drivers front wheel and plastic inner fender liner to access it. You may need new retainers for the fender liner.

Aug 10, 2009 | 1999 Lexus LS 400

1 Answer

My Whirlpool washer leaks when filling. We have located that it leaks from the plastic liner. Therefore leaking water onto floor.


Hi, The plastic liner you are talking about, is it the outer tub? If you could get me a model#, I could look this up for you.
Please let me know if I can help.

Vic

Jun 01, 2009 | Washing Machines

1 Answer

Fridgidare Model #LTF2940ESO won't start Error Message DDO


The code means the detergent door is open. There is a magnet placed inside the detergent door cover housing that has probably fallen out. This magnet completes a circuit when the door is closed. It usually happens when cleaning the compartment and can usually be found stuck somewhere on the washer metal body itself or somewhere on the path you took while taking it to wash it out. Take the detergent tray out and dissamble it by pushing open the plastic tabs that hold it together. Look for the small 1"long magnet. If there isn't one. take your tray assembly to a repair dealer and have them put a new one back in. It is just a few dollars and your problem will be solved.

Mar 20, 2009 | Frigidaire Washing Machines

1 Answer

I have the inner basket out of a Whirlpool LSR5132PQ Top Load Washerand I filled it with water to see water dripping out around the rubber gasket? in the center of the outer plastic liner basket. I'm...


wow ok you have there srprnigs to remove on the right side remove the clip spring by removing the 1/4 in nut driver head screw,,and do the same for the lef side,,,noe you have 1 more spring in the rear,,the counter balance spring this has 2 screws remove them,,now on the right side remove your pressure switch hose...go to the bottom of tub and remove your tub to pump hose..ok nw left hold tub up and twist back and forth and pull at the same time...reverse to put together..onthejob

Feb 02, 2009 | Whirlpool LSR5132PQ Top Load Washer

Not finding what you are looking for?
LG WM-2277HW Front Load Washer Logo

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6120 Answers

Brad Brown

Level 3 Expert

18378 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...