Raymarine A50D 5" Fishfinder / Chartplotter Combo - No Charts gold / platinum / tan / clear / red Logo

Question about Raymarine A50D 5" Fishfinder / Chartplotter Combo - No Charts gold / platinum / tan / clear / red

1 Answer

Raymarine a50d continuously resetting itself?

I have a Raymarine A50D fishfinder/gps which keeps turning itself on and off. It loads the raymarine screen then just goes to a black screen with the cursor but not one of the buttons will work. I have tried a factory reset but it doesn't even alow me to do that. There was 12.6 volts running from the battery so I dont think power is the issue. Is anybody able to help me with this?

Posted by Mitch1klan on

Ad

1 Answer

Barney R

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 9 Answers

If there's a memory card installed for maps, try starting up the unit with it removed. It's possible that the card might be corrupted and stalling the start-up sequence.

Posted on May 10, 2014

Testimonial: "Hi Barney, I just tried removing the Navionics chart card but it still does the same thing"

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

A50D

In general, you should be ablt to go to the settings page and one of the items will be units. Go to that page to change the units. Raymarine has an extensive on line set of usermanuals for more detail.
0helpful
1answer

50d

this happened to my camera. i just restsarted it if you can do that.
0helpful
1answer

Raymarine manuals for a50d

Gotcha covered!

The link below will give you access to your owner's manual for the A50D.

-Steve


Series A50 A50D A57D A70 A70D
0helpful
1answer

A50D turns on OK but every few minutes it 'reboots' itself as if shutting off and turning back on?

Hello
The fault is due to some firmware bugs. Just reset the system. Go to page [143] of its user manual, and make system reset and settings & data reset. OK.
1helpful
1answer

My raymarine a50d frozen in the same page, i need to reset the unit, could you help me how to do it?

To reset the A Series unit... power down the unit. Then PRESS AND HOLD the #1 Soft Key (left most button on below the display window) while you power up the unit. The unit display will come up quickly... then will go to a white screen that says " RESET IN 3...2...1...". Screen will then kick off. That is the MASTER RESET of the unit.

If you continue to see the unit lock up after that, if you have a seperate chart card that you use (Navonics), try running the unit with and without the card. You may find that the Chart Card is causing the unit to lock up. If not, you likely will have to send in the A50D for repair to NH.

Good Luck!! :)
0helpful
1answer
1helpful
1answer

I need a new power cable for a raymarine DS500X fishfinder. Where is a good place to buy?

Contact Raymarine or your nearest Raymarine dealer. Raymarine normally has those things on their website although it's a bit cryptic to find sometimes.
0helpful
2answers
1helpful
1answer

I Have a Raymarine Radar RL70CRC HSB2 the

If both plotter works but they have no comunikation
RESET the RL 70 AND L760
This is how it works
press the powerbutton when you have picture press the menu bottom
than systemsetup and than four seconds the menu bottom.
Do this on both plotter normaly after this it works again
Not finding what you are looking for?

280 views

Ask a Question

Usually answered in minutes!

Top Raymarine Computers & Internet Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Brad Brown

Level 3 Expert

19166 Answers

Cindy Wells

Level 3 Expert

6589 Answers

Are you a Raymarine Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...