Question about Under Armour Clothing Accessories

1 Answer

Bridge for The rubber that slides on adjustiable nose piece is wornen out

Posted by Anonymous on


1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Master
  • 85,239 Answers

We are not a parts supplier or locator.

Posted on Oct 30, 2018


1 Related Answer


  • 103 Answers

SOURCE: I have a pair similar

you can certainly replace your nose piece bridge by taking your cool sunglasses to the show room where you brought with the bill they have given you but you should have warrente or you need to pay for it but it wont cost much . or you can vist the site below ,for reparing your sunglass

Posted on Dec 02, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can not remove bit from 11223 EVS bosch rotohammer

Hopefully you don't have the wrong shank jammed in this because it can be a costly repair.
- Using a screwdriver, pull off the rubber dust cap #21 at the end of the nose & slide it out of your way.
- The shell #22 will also slide up out of your way
- Using a pick or small screwdriver, remove the snap ring #143 at the end of the nose & slide the 2 metal #144 & 1 rubber washer #31 out of your way
Slide the spacer tube #24 & stop sleeve #25 out of your way
Now you can access the 2 pawls #26 that hold the bit in place - you will have to assess what is jammed from here .
As I said, if you have a spline bit jammed in this SDS nose you may be looking at a whole new barrel because even if you extract the bit most of the time is does damage to the bit sleeve in the barrel.


Apr 08, 2014 | Bosch Drills

1 Answer

Is there anyway to tighten or slightly adjust oakley frogskins

You'll need to send it in to Oakley for the "Juliet Service". Call the 800 number and they will get you setup. Last time i had it done it was somewhere in the neighborhood of $60.00. But they redo the rubber in the nose bridge (you need a special tool), replace the nose bombs, temple shox, and ear socks. So for the price of the replacement rubber kit, you get a full service. The glasses come back feeling like new.

Jun 14, 2011 | Oakley Frogskin Sunglasses

1 Answer

Although the clamp holding the glass is tightened as tightly as it can be, the glass slips down. Any solution?

If you add a few little rubber pads (like those eyeglass nose pieces) between the metal and glass, it will solve your problem.

Jun 05, 2011 | American Standard 5 ft Sliding Shower Door

1 Answer

I have a pair of Tag sunglasses. I believe the model number is 6008 102 but the full numbers that are on one temple are 115/1 30 TH 6008 102 59 1703. There is a rubber nose piece that is mounted on a...

go to the official Tag Heuer website,, look for the retailers in your country chose the one nearest to you and contact him The name of the model is TH 6008 102

May 17, 2011 | Tag Heuer Clothing Accessories

1 Answer

Nose bridge rubber melt on my EVO Sunglass

this happened to me too, it can be replaced to the nearest glasses store.

They usually have something like this, and it's easy to change it.


Apr 16, 2011 | Nike Clothing Accessories

2 Answers

Rubber nose piece has split - barely hanging on


The part (or the glasses) must be replaced. Cheap repair done with superglue is not a good solution. Please contact Nike customer support using the link below:

Athletic Sport Sunglasses & Technology ' Nike

Mar 27, 2011 | Nike Counter Sunglasses

1 Answer

Replace rubber nose pieces

use small pin or maybe hairpin to unclog the said rubber.

Feb 01, 2011 | Tag Heuer TH 5104 Sunglasses

1 Answer

My framing nailgun hammer will not return

Driver not returning is usually caused by bent driver, worn lower bumper, loose piston oring and/or loose or broken check seal. Remove nails from magazine and push driver to top position; lightly tap nose of gun against rubber mat or soft wood. Driver should remain at top. If driver slides down, replace piston oring. If driver stays up remove head and pull out cylinder. Examine driver for bend, check lower bumper for missing pieces and look for check seal inplace around outside of cylinder. The check seal covers a row of holes in cylinder and could be oring or rubber band. It should fit snuggly around cylinder. Replace parts as needed. If all parts look good, examine upper bumper for cracks or missing pieces. It is located in the headvalve and is usually made of vinyl. When installing piston, check that it does not fit too tightly in cylinder. You should be able to push it down cylinder rather easily and stay in positon without dropping under its own weight. Lube all orings with silicone paste (sold at lowes in the plumbing or swimming pool departments). Good holidays

Nov 28, 2010 | Porta Nails Clipped Head 34 Degree Framing...

1 Answer

I have a pair similar to the EV0253 and the rubber on the nose piece bridge has disintergrated due to interaction with sunscreen. Can I replace the nose bridge piece?

you can certainly replace your nose piece bridge by taking your cool sunglasses to the show room where you brought with the bill they have given you but you should have warrente or you need to pay for it but it wont cost much . or you can vist the site below ,for reparing your sunglass

Nov 18, 2010 | Nike EV 0253 Sunglasses

Not finding what you are looking for?
Clothing Accessories Logo

Related Topics:

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Under Armour Clothing Accessories Experts

Jim Pattison

Level 3 Expert

1004 Answers

Tom Chichester

Level 3 Expert

56001 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

33353 Answers

Are you an Under Armour Clothing Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides