How to clean the fine filter - KitchenAid 24 in. KUDS25SH Built-in Dishwasher

check the hot side flow valve possible failure or debris

Try replacing or cleaning your spark plugs.

Remove and use fine bristle brushes assisted with a jet of air which will clean up the fine netting of the filter. It is important that the filters are occassionally cleaned so that there is no dirt accumulation within the lens unit that can reduce the life of the LAMP and save an expensive repair.

Remove the filter carefully from the unit. Now use a FINE brush to clean without damaging the fine netting of the filter. If there is a jet of air from a compressor or by using your vacuum cleaner in reverse,it will help a lot to assist the cleaning.
Also use a face mask as this being fine dust is not good to be inhaled.
If there is heavy dirt on the filter you can wash ONLY after cleaning off the dust . Drying must be done before refitting.

Keep in mind that there are two filters:

Coarse filter
The coarse filter collects large food particles
which cannot pass the outflow pump.
Lift out and empty the coarse filter as
necessary. Don't forget to replace it!

Fine filter
The residue which collects on the fine filter is
automatically rinsed off with each wash. The
fine filter should still be cleaned once or
twice a year.

1. Remove the fine filter by first turning the
filter's tubular strainer anti-clockwise and
then lifting it straight up with the coarse filter.

2. Clean with a dish washing brush. Ensure
that the edges are properly sealed

Download the manual and go to cleaning page.

Replace fuel filter after cleaning tank thouroughly, to clean tank remove fuel line at carb. Drain all fuel then leave line loose until you flush tank with carb. Cleaner then blow out tank with compressed air. Now install new fuel filter and check your fuel can for trash and water better yet just add fresh fuel.

Dishwasher filters are important to catch food particles and other debris. The dishwasher cleans small portions of food from the dishes, cooking pans and silverware. These particles must go somewhere. The drainage system on the washer may clog if filters are not present. Most Maytag dishwasher models have two types of filters, "Coarse" and "Fine." You should clean the "Coarse" filter after two or three wash loads. The "Fine" filter can wait for a cleaning for about 300 loads or three months.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); }); Difficulty: Easy Instructions Things You'll Need:

• Sink sponge

1. Empty the dishwasher. Remove all dishes including pots, pans and silverware.
   
2. Pull the bottom rack out as far as possible. The filters are under the basket on the Maytag dishwashers. It may be convenient to lift the rack out. Typically, if you lift, the wheels leave the track.
   
3. Remove the "Coarse" filter. This filter is a small, round knob in the middle of the "Fine" filter. A round knob is around the "Coarse" filter. Hold on to the handle and lift straight up.
   
4. Knock the contents of the "Coarse" filter into the garbage can. Run the faucet to remove smaller particles. Wipe the dishwasher filter with the sink sponge if debris is stuck-on. Push back into the filter holder when complete.
   
5. Take out the "Fine" filter. Turn the round knob that is around the "Coarse" filter counter-clockwise. Once the knob is loose, pull up. The "Fine" filter will come out of the dishwasher.
   
6. Rinse the "Fine" filter with the hot water faucet. Scrub with the sink sponge to remove any stuck-on fragments. Replace the filter into the dishwasher. Push down and turn the knob clockwise to tighten.
   

How did you clean the filters? I run mine through the dishwasher by themselves and it works pretty good. The tops and bottoms of the filters near the edges need to be wiped pretty clean.

dear sir/mam
clean pump means we should clean the filter provided in the pump line,in some models filter will be located inner bottom of the washing machine and outer bottom of the washing machine so please check it and clean the filter.

The fine fitler screws out by twisting the entire unit counter-clockwise. The threads are built into the filter unit itself. There are no screws to remove. Hope this helps.