Here list of Kitchen Aid range and oven codes.

4 Digit Failure Codes

F1 - E0 EEPROM communication error
F1 - E1 EEPROM checksum error
F1 - E2 UL A/D error
F1 - E4 Model ID error
F1 - E5 Calibration shifted
F1 - E6 Latch signal mismatch error
F1 - E9 Stack overflow
F1 - E3 Wiring harness cavity size does not match stored value
F2 - E0 Shorted touch pad
F2 - E1 Keypad cable connection error
F2 - E5 Cancel key drive line open
F2 - E6 Cancel key drive line open
F3 - E0 Oven temperature sensor (RTD) opened (upper oven on double oven models)
F3 - E1 Oven temperature sensor (RTD) shorted (upper oven on double oven models)
F3 - E2 Oven temperature is too high (Cook mode)
F3 - E3 Oven temperature is too high (Clean mode)
F3 - E4 Oven temperature sensor (RTD) opened (lower oven on double oven models)
F3 - E5 Oven temperature sensor (RTD) shorted (lower oven on double oven models)
F3 - E6 Drawer sensor open
F3 - E7 Warming drawer sensor shorted
F4 - E1 Meat probe malfunction - shorted
F5 - E0 Door Switch
F5 - E1 Self clean latch will not lock
F5 - E2 Latch during CLEAN error
F5 - E5 Self clean temperature not reached within 45 minutes.
F5 - E6 Door is open, but latch is locked
F5 - E7 Self clean latch will not unlock
F6 - E0 Return line not connected
F7 - E1 Common switch wire defective

Two digit codes:

F0 ERC Board failure
F1 ERC Board failure
F2 Oven temperature is too high
F3 Oven temperature sensor open
F4 Oven temperature sensor shorted
F5 ERC Board failure
F7 Function key stuck on ERC
F8 ERC Board failure
F9 Oven door lock failure

Microwave and Microwave combo error codes:

F1 - E3 or F1 - E4 Electronic control malfunction

F2 - E0 or F2 - E1 Keypad connection error

F2 - E3 Keypad held down too long, or keypad is shorted.

If you get an error code, try first resetting the code:
1. Disconnect power for about two minutes.
2. Connect back power.
3. If code re-appears, test and eventually replace faulty part.

Regards.

on Mar 27, 2010 | KitchenAid KHMS155LSS 1000 Watts Microwave...

2 Answers

Sanyo Microwave/Combi/Grill 900W em-g 47535 on front. Timer works but does not heat up code 1S on display. Any ideas

It hardly matters what code is showing because clearly the appliance is receiving power (timer works) and the internal workings of a microwave oven are potentially very dangerous and only competent people should open them up and fiddle around inside.

Sorry but the fact you need to ask shows you aren't a person competent enough to risk your neck inside a microwave. If it is a basic oven out of warranty it would be cheaper to replace it, if it is under warranty send it back and if it is a premium model it could be worth taking to the repair shop for a repair estimate.

Sep 23, 2016 | Sanyo Microwave Ovens

1 Answer

Mod.KHMS155LSS-1 Getting F-6 Fault code ????

Search Results

Combination Microwave Wall Oven - Error Code/Message ...

kitchenaid

microwave

error

code

error

cod

Over-the-Range Microwave - Error Code - Starts with F ...

kitchenaid

microwave

error

code

Kitchen Aid Oven Model # KEMS308SSS02 error msg - Lost ...

Feb 05, 2016 | KitchenAid Microwave Ovens

1 Answer

Display only shows 1s or 2s and and beeps when changing between the two Can not use any of the buttons nothing happens Tried switching off and unplugging but nothing Only thing in manual that...

Best to contact manufacturer website for this one.

Feb 15, 2015 | In Microwave Ovens

1 Answer

KitchenAid KHMS155LSS when press "bake potato" button,start flashing error F3

Question: Error Code - Oven - F3 Error Code - F3 E0 Answer Product Symptom:

Error Code/Message - Oven - F3 Error Code - F3 E0

Control displaying F3 E0:

There may be a problem with the Oven Temperature Sensor, or the associated wiring.

Power unit down by turning off the circuit breaker(s) for one (1) minute.

Power unit up by turning on the circuit breaker(s).

Monitor the oven for one (1) minute to ensure the error code does not display again.

Verify oven operation.

Jul 31, 2014 | KitchenAid KHMS155LSS 1000 Watts Microwave...

1 Answer

Not working keeps beeping

<- With a full model number from the tag on or in the oven, I may have been able to give you specific help.

Without that essential information, I can only give more general advice.

I would ask for additional information, but FixYa no longer notifies us experts when such inquiries have been answered.

So you would need to post a new help request with the full model number from the tag, and symptom details - what it's doing or not doing, and when it happens.

Jan 20, 2014 | Microwave Ovens

1 Answer

On 1992 Sharp conv/microwave cooked on m/w instead of hi mix roast accidently and there was a buzzing sound followed by oven power fail. Is it economically repairable please?

Replace it, parts are not available. Also this was not due to a setting it was due to age

Nov 09, 2012 | Sharp Microwave Ovens

1 Answer

My Onida Power solo 20 L 1200wqtts Microwave Oven domestic use model start moving turntable when the door is opened & stops when door closed.There is no oter problem like door & door Switches,

Possible that the switch or the lock is jammed or that the relay or main processor board is fault. Please take care that the microwave is not ON as this is dangerous.

Aug 18, 2012 | GE Microwave Ovens

1 Answer