Burner igniter won't click or work

Hi,

Under your knobs are burner switches, 3 of them are the same, so this will be a hit and miss on getting them but possible. Each burner should trigger the ignition system. This will be needed to be inspected to find out which one needs to be replace. If you get the right person to look over the unit they could tell you if it can be repaired. I worked on one about 3 years ago and it worked out fine. Good Luck and I hope this helped.

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

First, try to light the burner in question with a match. Just hold a match to the burner, then turn the gas on to low. If the burner doesn`t light, the problem is the gas supply to the burner. Next, lift the top cover and put the prop rod in the hole in the cover to support it. Hold a match to the left-front burner. Now, turn the control knob to "light". You should see the igniter spark and hear a snap. If this doesn`t happen, repeat this step with the left rear burner. If you hear the spark and snap.
If the igniter doesn`t work on the front left burner, but does on the rear left burner, the igniter does work. The problem is likely the control knob for the left front burner. The. Control knob includes the electrical switch the activates the igniter when you turn on that burner.

Replace the "igniter switch assembly". The igniter's are getting a weak spark and since you have one that will not spark at all, this is the usual problem. Here is the assembly to order.




The part comes with a 365 day, any part, any reason return policy.

Hi nancypp,

The ignition switches probably got wet.

Please follow my below Tip on how to fix it:

GAS STOVE CLICKING PROBLEM...

Kind Regards

JEDEMEYER1

* If this solution helped you, please accept it

Hi,
Here is a tip that I wrote to give details about why your cooktop will notspark to light the burners..

Cooktop Range Stove spark ignition does not work

heatman101

A few months ago I lost one igniter on the left front burner. It clicks and gas flows but wont ignite.Now when I turn on the left back burner, the gas still flows but I hear clicking on the right side, not from that burner. It wont light either.

Hi,

Here is a tip that I wrote to give details about why your cooktop will not spark to light the burners..

Cooktop Range Stove spark ignition does not work

heatman101

Hi,
Here is a tip that I wrote to help people troubleshoot problems with their cooktops not igniting.

Cooktop Range Stove spark ignition does not work
http://www.fixya.com/support/r5649407-cooktop_range_stove_spark_ignition_not

heatman101

If your top burners are not lighting or will not work, it is possible that the burners have become dirty or wet. Please follow the troubleshooting directions below before calling service:

1. Turn you burner to the Lite position:
   
   If you hear clicking or sparking, go to Step 2.
   
   If you do not, check your circuit breakers. If the circuit breaker is ok, we recommend that you schedule service by calling 1-800-432-2737 or schedule service online.
   
   
2. Clean the burner and electrode:
   
   First remove the burner grate, cap, and head. Use a needle or paper clip to poke through the holes on the burner head. Re-assemble and try the burner.
   
   Remove the burner grate, cap, and head. Even if it looks clean, wipe the tip of the electrode with a clean, dry paper towel and PRESS IT DOWN. Re-assemble and try the burner, again.
   
   Check to see if the burner works, If not, then go to Step 3.
   
   
3. Re-assemble - Make sure that each burner top matches its burner bottom. The burner top will lay flat if put on correctly.
   
   Check to see if the burner works, If not, then go to Step 4.
   
   
4. The spark igniter is operating properly, but the burner is still not lighting. At this point, we would recommend that you schedule service by calling 1-800-432-2737 or schedule service online.
   

no gas flow sounds like a bad gas regulato on the stove. as for the 5 year old ge profile with ignitors not working, you need a part called a spark modual