Question about Wareforce CG Underbar Glass Washer 208/230V

1 Answer

How to adjust water temp - Wareforce CG Underbar Glass Washer 208/230V

Posted by Anonymous on

Ad

1 Answer

ka4iup

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,062 Answers

Measure the temperature of the incoming water from your water source. Adjust water source temp to around 130 degrees, or what is required by data plate.

http://www.webstaurantstore.com/documents/pdf/wareforce_cg_service_manual.pdf

Posted on Mar 23, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I raise the temperature of my A O Water heater


Gas temp adjustment is on gas calve, make small adjustments 125 degrees is max allowed by plumbing code.
Electric is a little different .There may be two themostats one lower element and one upper element. Be sure to turn off power.
How to Adjust the Temperature on an AO Smith Electric Water Heater Hunker

Mar 03, 2018 | Water Water Heaters

1 Answer

How do i adjust water temperature


Start by turning breaker off to water heater,then remove both hi & lo panels there you will see tstats, with a screwdriver adjust to desired temp. 2 tstats 1for each heating element

Jan 15, 2015 | Water Water Heaters

1 Answer

Adjusting Apollo hot water tank


I am not sure what you are asking, But i am going to assume that you want to know about changing the Temp on the heater for inside the house.
If the floor heat was installed properly than it should have a temperture manifold or adjustable thermostat for seperate heating.
You need to find the thermostat or manifold for the garage heat and set it at what ever temp you want the garage to stay at.
Then you can change the A B C knob to a higher setting A is cold B is warm ac is hot. So Increase your temp setting on the heater and this will increase your house water temp for hotter showers and faucet temps. However, they recommend not setting the temp above 120 degrees to prevent severe burns.
If you have a newer home increasing the Hot water heater temp setting may not change the temp at the shower or faucets if you have scald guard faucets installed in the house. This will require adjusting the scald guard valves on each faucet.
I recommend using a candy thermometer or digital thermometer to check the faucet and shower Temp prior to using them and make sure that you inform everyone in the house after you change the temp so that no one gets scalded.
I hope this answers you question, feel free to contact me if you need more help!
DR Wilkins

Oct 15, 2013 | Water Heaters

1 Answer

Unit not coming on. There is water, gas, and electric. I can adjust digital read out for water temp, but unit is non responsive.


have you reset boiler and gone through start up procedures.if so it sounds like an ignition problem? you need to explain what happened before you adjusted the water temp and why?

Dec 11, 2012 | Rinnai 351-R50LSiN - Water Heaters -...

1 Answer

I have a instantaneous water system 10H Hydropower ...did not get a manual when installed....I need to have hotter water as it's winter and the water is like warm...not sure what to adjust...opened...


take the cover off the 10 h unit light up the burner by turning on the tap turn the water flow tap on the front of unit (white knob) clock wise slowly feel hot water pipe coming out off unit when temp increases put cover back on check temp at sink if too hot turn knob anti clock wise

May 23, 2011 | Bosch Water Heaters

1 Answer

How do i adjust the temp in my water heater?


Down near the bottom is a gas valve. Adjustment should be there if it is a gas type heater.

Nov 23, 2010 | General Electric GE SmartWater Household...

1 Answer

How do i adjust the water tempature from the hot taps ?


you don't adjust hot water temp from the taps...

you can only adjust from the water heater.

what water heater do you have?

Aug 14, 2010 | Water Heaters

1 Answer

Combi boiler hot water far to hot.


Yes the temp can be adjusted, the dial is behind the cover. Turn off power before removing cover.

Sep 11, 2009 | Water Heaters

1 Answer

Adjusting water temp


Behind the handle there is usually a scald gaurd on the newer faucets. You can adjust it from there. If your not sure, follow this link and download the installation instructions to your faucet. There you will find how to adjust it step by step. http://www.hansgrohe-usa.com/us_en

Mar 05, 2009 | Hansgrohe Thermo II Rough-In Valve Chrome...

Not finding what you are looking for?
Wareforce CG Underbar Glass Washer 208/230V Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wareforce Water Heaters Experts

Brad Brown

Level 3 Expert

18401 Answers

Paul Carew

Level 3 Expert

3512 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Wareforce Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...