Question about Hotpoint Aquarius WF220 Front Load Washer

Open Question

Pumps out but wont spin fast enough

Pumps out water but doesnt spin fast enough

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag Neptune Front Load Washer Model MAH5500BWW


You say your belt is a little loose. When the motor starts to spin the belt may become more loose, causing the belt to not spin the pump at full capacity. I would suggest you change the belt. I think you will find your problem. Good Luck Friend.

Sep 24, 2018 | Maytag Washing Machines

1 Answer

What causes the water not to spin out of the clothes?


Hi, it means that the machine is not spinning fast enough and pumping the water away. If its not spinning enough then you have to get the machine looked at as its not clicking on in the cycle for it to spin fast enough. You also have to have it set to wash cycle that has a fast spin. If it is spinning fast then you have to look at the pump to make sure its pumping the water away.

Mar 18, 2016 | Washing Machines

1 Answer

My maytag washer does not spin fast enough to get the water out of the clothes. Please advise


Randall, the high speed spin failure can be caused by a number of issues. I would suggest starting the machine without any clothes in it. Once it has filled, make sure the door lock light is on and that the door is, in fact, locked. If the light is not on, or if the door is not actually locked, either the door lock assembly or the control panel is at fault.

If the light is on and the door is locked, stop the wash cycle and start a drain and spin cycle to see if all of the water is pumped out of the drum. All water should be pumped out within 10-15 seconds. If excess water is in the drum, the high speed spin will not start.

Mar 06, 2015 | Maytag Washing Machines

1 Answer

Speedqueen awm270-3062 why does machine cut out on spin cycle and when u manualy remove water it then spins


either the water doesnt get pumped out fast enough
or the motor has an issue prob its brushes need replaced

Dec 10, 2014 | Washing Machines

1 Answer

Dishwasher leaves upper rack dishes dirty. It's Whirlpool Quiet Partner II


Your water pressure is not high enough in the dishwasher to wash the dishes on the top rack. The most common reason is that the pump in your dishwasher cannot pump fast enough to keep the water pressure up. That is because the shaft that drives the pump impeller also drives the macerator cutter that grinds up bits of food fine enough for it to pass through the screen and out to the drain. Over time, small bits of bone, broken glass, eggshell, and other items that are too strong to be cut up by the cutter end up sitting in the area where it has to spin, and they prevent it from spinning fast enough to pump enough water to the top rack with any pressure. It is simple enough to repair. You need to take out the racks, remove the bottom arm and clean out the little macerator. Once that is done, it should work great again.

Feb 22, 2011 | Whirlpool 24 in. DU900PCD Built-in...

1 Answer

Is leaking water at the back and running in the floor the hoses are tight drain pipe is in right


Here's what I've seen. Water will be full, machine goes to spin/drain and expects the water to be pumped out as predicted. If pump is clogged, the pump cannnot pump out water quickly enough and the spinning causes the water to spill over the back of the tub, between the tub and balance ring. The balance ring is never sealed tightly to the tub so water will get through. Fill the basket with water, extra high, hold lid switch down, and see if it drains out fast enough so water doesn't spin out. If this is the case, pull pump, dislodge debris.

Oct 02, 2010 | Maytag Washing Machines

1 Answer

Will not spin fast enough on final spin cycle to


ITS POSSABLE ITS NOT PUMPING FAST ENOUGH. CHECK THE DRAIN HOSE AND MAKE SURE IT HAS NO KINK. IF THATS OK IT MAY HAVE A BUILDUP OF SOAP. RUN A EMPTY CYCLE WITH NO SOAP. IF THAT DONT WORK YOU NEED A REPIARMAN TO CLEAN OR REPLACE THE PUMP.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

May 15, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Kenmore washer want spin out allthe water buy a new water pump


If it is pumping out some of the water then the pump is probably okay and the problem is probably in the clutch or belt slipping not spinning the clothes fast enough.

Mar 05, 2010 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore 90 Series washer needs two spins to remove water


We have exact same washer. It is 11 years old. We are at a point where we have to spin it 7 times and then still isn't too dry. It dies yesterday a very loud death. Mentioning this here because it could be a foreshadowing of your Kenmore 90's future.

Dec 29, 2008 | Washing Machines

2 Answers

WASHER WILL NOT SPIN


replace the belt

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Dec 28, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF220 Front Load Washer Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

gbob59

Level 3 Expert

3063 Answers

Eric Taylor

Level 3 Expert

590 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...