When you press the on button it blinks 5 times then goes off

follow these steps
1) Press ST1+READY button together
2)Turn on the tvs speed 40plus passbook printer
3) The 4 LED will blink 4 times. Release the button ST1+READY immediately after 4 blinks
4)PRESS ST1 - ST1+READY+EJECT starts blinking
5)again PRESS ST1 - ST1+EJECT+ST2 starts blinking
6)again PRESS ST1 - ST1+EJECT starts blinking
7)again PRESS ST1 - ST1+EJECT starts blinking
8)again PRESS ST1 - READY+EJECT starts blinking
9) printer is READY wait and PUT PAPER.
10) The paper goes in and comes out 3 times. will take about 2 minutes.
11) Paper ejects automatically after printing.
12) turn off the printer and turn it on.

shutdown is happening= If set has been unplugged plug it back in and turn set on--when green power light goes off in a few seconds:

On front of set (not the remote) press and hold both the Menu and Input (Device) buttons at same time and hold for at least 5 seconds---then release both.

Power light will blink an error code like 2 blinks, 2 blinks pause and repeat it for a total of 5 times.

Let me know what error code is and I will tell you what it means.

SD TECH

IF power light comes on for a moment and then goes off:

Mitsubishi self check: MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.

SD TECH

this should fix your problem
HOW TO USE YOUR TC100 TIME CLOCK Step 1: Remove the front cover - see enclosed instruction sheet on page 5. Step 2: Program the Date & Time and Print Method using the 3 buttons: Mode, Select, Setting: Date & Time: Press the Mode button. The Hour will start blinking. Press the Setting button until the correct hour is displayed. Press Select to set the hour shown. The Minutes will blink. Press Setting until the correct minutes are displayed. Press Select to set the minutes shown. The Seconds will blink. To set the seconds at 00, press the Setting button. Press Select. The Year will blink. Press the Setting button until the desired year is shown. Press Select to set the year shown. The Month will blink. Press Setting until the correct month is shown. Press Select to set the month shown. The Day blinks. Press Setting until the correct day is shown. Press Select to set the day shown. Print Method: Press the Mode button until P5 (Program Mode 5 for Print Format) is displayed. Press Setting to choose one of the following Print Methods. The TC100 has two settings for print activation: Manual or Automatic 1 = Automatic (default setting) - The TC100 automatically prints when the time card is inserted. 2 = Manual - After inserting the time card, press the Print Button to activate printing. Press Select to confirm the Print Method chosen. Press Mode

Do the self check when power light goes out:

ON front of set (not remote) press and hold both the Menu and Input (Device) buttons at same time for 5 seconds or longer and release both buttons.

Power light will blink a two digit error code like 2 blinks, 2 blinks, a pause and repeat it several times.

Let me know code.


SD TECH

When the power light comes on and then goes out, on the front of the set press both the MENU and INPUT buttons at the same time and hold them both in for at least 5 seconds and then release both buttons.

The power light will blink a 2 digit error code and repeat it at least 5 times.

The most common error will be 2 blinks, 2 blinks- a pause and then it will repeat it for a total of at least 5 times.

To get it to repeat this--you have to unplug the set, try to turn it on again and repeat the process.

The error codes are to try to narrow down where the problem is.

Let me know what you find and I will tell you what it means.

If this told you something you did not know rate this solution as very helpful as I do this here for free.

MAKE A COMMENT HERE and I will help.

SD TECH

Do the self check it should have: when shuts down and green light goes out: On the front of the set press and hold both input and menu buttons at the same time for at least 5 seconds and then release both.

Power light on set should blink a two digit error code: like 2 blink,2 blink, pause and repeat it at least 5 times total.


Let me know what error code and I will tell you what it means.


If this has helped you, rate this solution as I do this here for free.



SD TECH

when you turn it on and then the green power light goes off:

On the front of the set press and hold both the Menu and Input buttons at the same time for at least 5 seconds and then release both.

The green power light should blink a error code at least 5 times: most common is 2 blinks, pause and 2 blinks----

Let me know what error code you find and I will tell you what it means--2,2 is the most easy to fix and common.


SD TECH

NEXT TIME IT SHUTS DOWN: when green light goes out on THE FRONT OF THE SET: press and hold BOTH the menu and input buttons at the same time for at least 5 seconds and then release both.

This is the self check this model has---power light should blink a two digit code---for example--two blinks, a pause and two blinks and the set will repeat the error code about 10 times.

1 blinks and then 2 blinks is NO ERROR DETECTED
2 blinks and then 2 blinks is short protect

ETC.....Let me know if you get an error code and I will tell you what the problem is---hope you find 2,2 that is the most common and the most easy to repair.

SD TECH

Depends on how many times it blinks,just count the blinks Example: if it blink 2 times then pauses and blink 5 times then the code would be 25 and so on

Once you have this code,please post it.