Question about Konica Minolta bizhub 350 All-In-One Laser Printer

1 Answer

Mac address for bizhub 161f

I have link lights on NIC but when printing a config page it reports there is no NIC installed. I have reset device back to factory defaults. Is there some other way of finding the MAC / hardware address of the device?

Posted by Anonymous on

Ad

1 Answer

Norman J Weimar Jr

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Konica Minolta Master
  • 6,960 Answers

Are the print driver installed properly was a ip address given to the machine

try this site


Self Help Product Support Konica Minolta Business Solutions Inc

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Posted on Jan 10, 2016

Ad

5 Related Answers

Anonymous

  • 167 Answers

SOURCE: Bizhub C250

In the Utility Menu you can set the default settings for most functions. Set the copier to the state you wish it to be in. Under the utility menu there is a default setting button. This will allow you to set the current state to the default as well as reset to factory default.

Posted on Jan 08, 2008

Ad

Anonymous

  • 167 Answers

SOURCE: C252 Mac issue

You need to set the options in the printer driver as well. You need to tell it just what features you have installed on the device.

Posted on Jan 08, 2008

Anonymous

  • 1 Answer

SOURCE: I cant install konica Minolta bizhub C351 on my mac. please HELP

To print via IP on MAC  type IP address in queue type print ,name the printer and  the correct driver/ fy...35/

Posted on Jun 19, 2008

taminol

taminol

  • 62 Answers

SOURCE: c14a3 error code konica minolta bizhub 161f

Hi jdt_mk,

Sorry to hear you have a C-14a3 code.
In my experience, this code spells disaster for the 161f.
The image reader has failed. The part can be replaced, but the cost would almost outweigh the cost of replacing the machine.
I have personally had to deal with two 161f with the same code.
Both times we changed the machine (because it was on contract).

Sorry it's not good news

Posted on Jan 29, 2010

Anonymous

  • 1 Answer

SOURCE: konica minolta bizhub c350 installer for mac

You have to have a fiery unit (external controler) to use the C350 With a Mac because the c350 dosnt come with appletalk in the software. IC-401 Is the model number of the controller you will need to connect the c350 to any kind of mac for printing / scanning.

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Network Interface is out of service


You can try resetting the NIC for future reference.

You'll need to print a NIC page first. Here are instructions on how to do that:
Print NIC Page with Network Info

Then go to the machine and do the following:

System Settings
Admin Password
The default password is admin
ok, ok
Network settings
Scroll down to Reset the NIC, execute.

Once the machine has rebooted go back to the network settings, then IP address settings. Uncheck the DHCP box then enter the IP address, Subnet Mask, and IP gateway from the NIC page you printed out.

Hope this helps.

Jan 27, 2014 | Sharp Office Equipment & Supplies

1 Answer

My brother laser will not reset back to factory defaults


If you are using the printer in a LAN or Wireless LAN, you must assign to it an IP address compatible with your network. You do that by opening the Web admin interface of your router and assigning to the printer an address that is still free. Try 192.168.1.178 but that depends on the default gateway (192.168.1.1) that you defined for your router.

Aug 02, 2012 | Brother Office Equipment & Supplies

1 Answer

Reset hp 1515n


? Restore defaults-used to reset all customer-accessible menu settings back to the factory default
settings (except language) via the control panel or software
NOTE: This service menu item does not reset factory-settable settings, including formatter
number, page counts, factory paper settings, language, and so on.
NOTE: Before restoring defaults, print a menu structure report and a configuration page. Use the
information on these pages to reset customer-specific settings.
CAUTION: All HP Jetdirect settings are also reset. Be sure to print a configuration page before
restoring defaults. Make note of the IP address that is listed on the Jetdirect configuration page. You might need to restore the IP address after performing a cold reset.
Restore the factory-set defaults on the (HP Color LaserJet CP1510 Series Printer

1. Press OK to open the menus.
2. Use the Left arrow or the Right arrow button to select Service, and then press OK (Select).
3. Use the Left arrow or the Right arrow button to select Restore defaults, and then press OK.
The product automatically restarts.

Jul 13, 2011 | HP LaserJet CP1515n Printer

1 Answer

HP P3015 suddenly printing very slowly - about a page a minute


If you unplug the cable from the printer to the PC and print the MENU MAP, does it print slow or at normal speed?
If it prints slow, try following the directions below.
If it prints at normal speed, try removing the printer from the print queue and reinstalling it. Also, download the PCL5 drivers and reinstall it.
Good Luck.

Print a MENU MAP and a CONFIG page.
You will need this info to put the settings back in the printer.
1. Turn the device off.
2. Turn the device on. When the memory count begins, press and hold the CHECK MARK button. Continue holding
down this button until all three device control-panel lights flash once and then remain on. This
might take up to 10 seconds.
3. After the message SELECT LANGUAGE appears on the display, press the ^ button
until COLD RESET is highlighted.
4. Press CHECK MARK . The device performs a cold reset and then continues its power-on sequence.
5. Check all I/O settings and reset any customer-set device configuration values.

COLD RESET sets ALL control panel menu items, including network settings back to factory defaults.
This is where the MENU MAP and CONFIG info come into play.

Feb 09, 2011 | HP P3015 Laser Printer

1 Answer

How do i perform a cold reset on a laserjet 2600n printer


Via the Control Panel: The Resets menu makes it possible to reset factory settings, disable and enable Powersave, and update the printer after new supplies are installed. Configure device menu The Configure device menu makes it possible to change the printer's default print settings, adjust the print quality, change the system's configuration and I/O options, and reset the printer's default settings RESTORE FACTORY SETTINGS :Makes it possible to clear the page buffer, remove all perishable personality data, reset the printing environment, and return all default settings to factory defaults. Press Menu or (Select) to enter the MENUS.
  1. Press (Down Arrow) to highlight Configure device menu .
  2. Press (Select) to select Configure device menu
  3. Press (down arrow) to System setup menu
  4. Press (select) System setup menu
  5. Press (select) Resets menu
  6. Select RESTORE FACTORY SETTINGS.


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Dec 03, 2010 | HP LaserJet 4600dn Color Printer

1 Answer

My hp 5200 printer prints extra sets of multi page documents when only 1 copy has been selected for output. Is this a printer setting that I can change? Is there someway to reset to its default settings?


Here ya go sir, this is a cold reset option and it will reset all back to factory defaults so if there are setting you want back, you may want to print out a config report prior to resetting...

1. Turn the printer off.

2. Turn the printer on. When the printer begins its memory count, press and hold down until all
three printer control-panel lights flash once and then remain on. This might take up to 10 seconds.

3. Release .

4. After SELECT LANGUAGE appears on the control-panel display, press or until COLD
RESET
is highlighted.

5. Press . The printer performs a cold reset and then continues its power-on sequence.

6. Check all I/O settings and reset any customer-set printer configuration values.

hope this helps and if so please mark this as a fixya for me sir...

Jul 02, 2010 | HP LaserJet 5200 Printer

1 Answer

Lexmark c534 printed pictures are very dark


Hi,
Just to be sure that this is not a software problem try the following. Go to printers menu and select Reports then Print Demo Page. That will print a Demo page which is a picture. If that picture is very dark as well then the problem is with hardware. You can start by resetting all values to factory defaults. To do that turn the printer off then press and hold the check mark and the Right Pointing arrow, then power the printer on. Wait until the little clock appears and then release the buttons. You will be entering the Config Menu. Then using the arrow buttons search for Factory Defaults and select using the Check mark button. That will reset the Factory Defaults and will make sure that all the settings go back to what they were before. Then Print Another Demo Page if the problem persisted then try to check the life of the Photoconductors and make sure they are not contaminated. This could also be a problem with the High Voltage Power Supply, if thats the case it will probably have to be replace.



Feb 04, 2010 | Lexmark C534N Printer

1 Answer

Activity Reports


First of all, Back up your configuration by printing it.
[Menu] --> [Reports/Lists] --> [User Data List]

then go back to main menu

[Menu] --> [#] , it will display #SSSW
Use the [+] [-] buttons till you see [#CLEAR]
Press [OK]

That resets all the configs and status flags.
With the initial config in hand, you are ready to setup you device and we all live happily ever after.

Try it out, it works perfectly and on most models

Aug 28, 2007 | Canon LaserBase MF5650 All-In-One Printer

7 Answers

How do I reset access password?


Thanks. I actually found out that it had never been configured - here is the standard factory access info: All Oki network printing devices support configuration changes via a standard web browser such as Internet Explorer or Netscape Navigator. When applying a configuration change to a device the user is prompted for a user name and password. The following details should be entered: User Name: root Password: last six digits of the MAC address* *You can find the MAC address on the network summary web page or by printing off a menu from the printer.

Nov 22, 2006 | Okilan 8100e Print Server

Not finding what you are looking for?
Konica Minolta bizhub 350 All-In-One Laser Printer Logo

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers

carpediemweb

Level 1 Expert

51 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...