Question about General Electric WCVH6800J Front Load Washer

Open Question

Won't go into test mode

Fills for rinse sits there than drains but will not agitate but agitates on wash

Posted by Anonymous on

Ad

2 Related Answers

Anonymous

  • 572 Answers

SOURCE: Wont spin or agitate. Fills, sits there through

check the belt in the back.

Posted on Feb 05, 2010


Anonymous

  • 44 Answers

SOURCE: fills turns counterclockwise one turn then

Try to clean the discharge pump filter first (Instructions in the Use/Care manual).

If the drain pump is working, it's most likely related to the pressure switch. Check out these postings:

http://www.fixya.com/support/t9807344-ge_front_load_washer_stops_45_min_35_min
http://www.fixya.com/support/t8933273-general_electirc_washer_model

Posted on Jul 28, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why does not agitate on rinse cycle

It shouldn't agitate on rinse cycle. ''Quick wash'' is the last type of ''cycle'' you can select that the machine will ''agitate.'' On ''rinse'' cycle, it will fill with water and then simply drain & spin.
1helpful
1answer

Need info about extra rinse cycye

there should be agitation..dont know unless its not making the connection in the control head..
0helpful
1answer

My hotpoint washer wont agitate spin or drain. it makes a clunking noise when you try to change the cycles manually

The draining problem could be something stuck in the pump. A easy fix just take it apart and get whatever is in it out of there. The agitator sits atop an agitator drive block. The spline on these tends to strip out. Yank off the agitator (it just snaps on) and replace the drive block.

SERVICE MANUAL

My page shows more HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

0helpful
1answer

Please describe a typical washing cycle to me on the RTW4440XQ Roper 3.1 Cu. Ft. Top-Load Washer, please.

The typical cycle is;
fills to selected water level
agitates wash cycle
drains wash water
spins wash cycle
fills to selected water level on rinse cycle
agitates on rinse cycle
drains rinse water
spins final time
end of cycle
32helpful
1answer

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE please show me a diagram
0helpful
1answer

Whirlpool top load washer no low-speed agitation. The unit fills, starts the wash cycle with normal agitation, but after a few minutes it just sits there soaking until the it's time to drain/spin. Drains...

Either the wire going to motor for non working speed is loose or damaged, or motor is bad. It could also possibly be timer not sending power to motor for that speed.
0helpful
1answer

Kicking out water during wash cycle - spin instead of agitation

Hi,
Try these

  1. Check the drain hose, it should be at least as high as the top of the wash tub, about 38 inches.
  2. The drain hose must sit loosely in the house drain. Do not seal the air gap around the drain hose or a siphon will occur.
  3. Check the drain control lever
  4. Test the drain control coils
  5. Check the cam bar
pls rate my suggestion..
Not finding what you are looking for?
General Electric WCVH6800J Front Load Washer Logo

Related Topics:

31 views

Ask a Question

Usually answered in minutes!

Top General Washing Machines Experts

Oloyede Monsuru

Level 3 Expert

1468 Answers

sheakhly

Level 1 Expert

33 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a General Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...