ENS202 installation and setup

PROPHETIC CHANNEL SETTINGS on Your DECODER(DSTV)
Step: 1 Press menu Select "Advanced Options" Select "Dish Installation" Enter the pin "9949"
Select "Network Configuration" Select "Network 2 Setup" NB: Leave "Network 1 Setup (Home)" unchanged!! Set Signal Setup to "Enabled" by selecting it, and moving left or right Set Frequency to "11170" Set Symbol Rate to "26652 Set Polarization to "Vertical" Set FEC to "3/4? Select "Accept these settings"
Step: 2 Select "Network 2 Setup" Set Signal Setup to "Enabled" Set Frequency to "12682" Set Symbol Rate to "26657 Set Polarization to "Horizontal" Set FEC to "1/2? Select "Accept these settings"
Step: 3 Select "Network 3 Setup" Set Signal Setup to "Enabled" Set Frequency to "12722" Set Symbol Rate to "26657 Set Polarization to "Vertical" Set FEC to "1/2? Select "Accept these settings"
Step: 4 "Accept these settings" to go back to the "Dish Installation" menu then Select "Scan All Networks" Your decoder will go into scanning mode and might take a while to scan all networks. Do not interrupt the process even if it seams to take longer than you expected! Once completed, your picture will return as normal.
ENJOY WATCHING PROPHETIC CHANNEL.
http://electronicshelponline.blogspot.com/
http://schematicscom.blogspot.com/
http://electrotechnician.blogspot.com/

Are you trying to setup Linksys router?
You can run the installation CD to setup Linksys router or you can do it without installation CD also.
Connect the computer to the router with the Ethernet cable.
Open the setup page of the router.
Change the Internet connection settings.
Create a new wireless network.
Connect to the network.

I will suggest you a website that you can try to setup your Linksys wireless router without installation CD.

Print the network settings page to identify if your printer is connected to your wireless network:

1. Press Setup on the printer operator panel.

2. Press the right or left arrow button until Network Setup is displayed, press OK.

3. Press OK at Print Setup Page.

4. Press OK when prompted to Load Paper.

5. Press OK. The network settings page will now print.

Check the Network Card Status, SSID, Trouble Code, TCP/IP Address. SSID should be the name of your wireless network. Otherwise, you may need to reset the printer's wireless network settings.

How to reset network settings:

1. Press Setup.

2. Press the right or left arrow button until Network Setup is displayed, press OK.

3. Press the right or left arrow button until Reset Network Adapter Defaults is displayed, press OK.

4. Press the right or left arrow button to display Yes, pressOK.

Once the Wi-Fi light turns on to solid orange, run the Lexmark Wireless Setup Assistant on your Mac.

Setup cannot find the required setup controller file. Either there was a network error, an error reading from the CD, DVD, or other installation media, or a problem with the package you downloaded.

Hi,

Click on the link to resolve printing issue on wireless network -> Link
Click on the link to find out if the HP Printer is on wireless network on not -> Link

To Setup the printer on wireless network, follow the steps below
1. Press the SETUP Button printer front panel
2. Scroll to Network - Press OK
3. Scroll to Wireless Setup Wizard - Press Ok
The printer will start searching for wireless router.
Choose the SSID ( Network ) and enter SSID ( network key if setup ) and Press OK
You should get a message as Printer Wireless Setup complete.

Run the HP Printer Software Disk and Choose Add a printer and Choose Wireless Installation and follow the instructions on the screen to complete the setup

You are ready to Print and Scan

1. Define your Star Micronics Printers device model TSP600
2. Define your operating system to install your Star Micronics Printers device
3. Search Printers driver category
4. Find Star Micronics Printers driver
5. Select Star Micronics TSP600 Printer Network Setup Utility Ver. 2.0.1 Windows XP, 2000, ME, 98, 95
6. Download Star Micronics TSP600 Printer Network Setup Utility Ver. 2.0.1 Windows XP, 2000, ME, 98, 95
7. Install Star Micronics TSP600 Printer Network Setup Utility Ver. 2.0.1 Windows XP, 2000, ME, 98, 95
8. Restart or reboot your computer to finish your driver installation.

Download here:

http://www.opendrivers.com/driver/247183/star-micronics-tsp600-printer-network-setup-utility-ver.-2.0.1-windows-xp-2000-me-98-95-free-download.html

Hi,

Here I find your printer is not a network printer hence directly accessing is not possible . You need to configure the printer to one of the PC and share the printer access rights . Then take a another PC and search for the computer name ed : \\resdc
When you find the PC double click and you shall find the printer .Click on thee printer and connect.

hi
5200 series are both wired and wireless network ready printers
so i will tell you the steps to configure it wireless on the computer

for that you should have a wireless router and the computers should be connected to the router
now follow the following instruction to configure the printer

Connecting the unit to the computer


Press the Setup button on the all-in-one.
Press the arrow buttons until Network displays and then press OK . The Network menu displays.
Press the arrow buttons until Wireless Setup Wizard displays and then press OK .
Follow the instructions in the Wireless Setup Wizard.
it will ask for the router password you should know the router password to connect
After the all-in-one connects to the network, install the product software on the computer.

insert the software cd and install it using network wired/wireless
and complete the installation and similarly install on the other computer as well

and if you face any problem do let us know

Does the printer have an IP already assigned to it?

Print out a network settings page:

Printing a network setup page
If the printer is attached to a network, print a network setup page to verify the network connection. This page also
provides important information that aids network printing configuration.
1 Make sure the printer is on and Ready appears.
2 From the control panel, press .
3 Press until Reports appears, and then press .
4 Press until Network Setup Page appears, and then press .
After the network setup page prints, Ready appears.
Note: If an optional internal print server is installed, Print Network <x> Setup Page appears.
5 Check the first section on the network setup page, and confirm that Status is “Connected.”
If Status is “Not Connected,” the LAN drop may not be active, or the network cable may be malfunctioning.

If that is an IP not on your network, then you need to change that IP to an unassigned IP that is on your network.

You can do that by typing in the IP of the printer into a web browser (example: Http://ipaddress)
Then you should be able to modify the IP address from here.

Once the printer is on your network, make sure you have drivers for it installed and then just map any worksttaion to it.

Did you setup your network connection
Go to control panel network setup and follow instructions make sure both computers are on the same network
EG : network name = workgroups or similar
And also is your router setup properly