Question about Sony KP-53V75 53" Rear Projection Television

1 Answer

Blue shadow Images of people have a blue shadow on the left of the image and the "+" control in the panel displays the blue off center to the right, is there is fix for this?

Posted by rmv999 on

  • drumatune Jan 06, 2008

    I tried ti align the colors 2 or 3 times and can't seem to get them to go together I have a green shadow to the top and left of every thing,,, when I see print it looks curved with 2 colors (red and green) can I fix this?  

  • akb777 May 11, 2009

    I have the same problem and have yet to get an answer if you find a fix let me know

×

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 317 Answers

Call tech ...suggest to ck. blue coolant..and c-chips.

Posted on Nov 26, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Picture is distorted from center on my 65


You do have a failure in the convergence circuit of your set. If you are good at soldering you can replace the IC's yourself. They are on the large circuit board on the left side of the set looking from the back, and attached to a large aluminum heat sink. If you don't feel comfortable doing that, I reccomend removing the board and sending it to PTS corp in Indiana. They are pretty reasonable repairing boards, and a lot less than buying a new one.

May 31, 2009 | Sony Grand WEGA KDP-65WS550 65" Rear...

1 Answer

Picture is distorted from center on my 65" Sony projection TV.


hi. this will be an easy fix for you if you are a good solder. you will need to replace the convergence chip that is located on the PC board(main). this chip is damaged and it has failed due to this damage that has occurred. click below for your new convergence chip(stk).

CLICK HERE

May 21, 2009 | Sony Grand WEGA KDP-65WS550 65" Rear...

2 Answers

Shadowing


GOOD DAY ND GOOD LUCK;

TRY THIS, IT WILL CORRECT CONCERN:

50V500 ONLY
GHOST: May be described as "Out of Convergence" but ghost is still attached to main image.
CONDITION:
A "ghost image" appearing to the left or right of images in the picture. Can be varying shades of a primary color (red, green, or blue) as well as gray. Can easily be seen in the 4 x 3 mode, at the edges of the picture.
CORRECTION:

To correct the problem, please do as follows:
  1. Access I2C Menu. (See page 57 of the Service Manual).
  1. To enter the I2C Service Menu, with power off, (on the front control panel) press and hold the INPUT button. Then press the POWER button for two seconds. The following Service Menu will appear.
03b_ghost_image01.gif Figure 1
  1. BEFORE CONTINUING: CONFIRM THAT THE R, G and B DRIVE ARE SET AT 40.
  • Be sure to press SELECT after each change to SAVE the new Data.


  1. Using the Remote Control joy stick, scroll down to next page (see Figure 2) until LCD ADJUST is highlighted.
03b_ghost_image02.gif Figure 2
  1. Move the joy stick to the right to cursor right once. The next page will appear with the word GHOST highlighted.
  2. Cursor right again, and a white screen will appear with a BLACK SQUARE in the center, as in Figure 3. You will see LCD ADJUST, followed by “SHP” and a number (value).
03b_ghost_image03.gif
Figure 3

  1. If the unit is out of adjustment, you will see a gray ghost on either side of the black square. Move the joystick to the right or to the left until the ghost disappears. The number values will change up or down.
    • If the ghost adjustment is off with a lower value, there will be a ghost to the left of the square.
    • If the ghost adjustment is off with a higher value, there will be a ghost to the right of the square.
  2. Once you get the square to look good without ghosts, press "SELECT" to save any data values that have been changed.
  3. Press the "EXIT" button three times to return to normal picture.
  4. Adjustment is completed
  5. I HOPE THIS WAS HELPFUL, big IRISH.




Jul 26, 2008 | Hitachi 50V500 50 in. HD-Ready LCD...

1 Answer

Color distortion


There are failures occuring in the scann and convergence circuits. This may not be feasible to service.

Jerry G.

Dec 14, 2007 | Sony KP-43T90 43" Rear Projection...

1 Answer

WS-55807: Images are dark on right side of display, but will go away after 3-4 hours.


you could be on the right track get some freeze spray and go around all the parts to see if you can make it act up, same with heatgun or hair dryer when first turned on heat one area at a time to narrow your problem down

Oct 21, 2007 | Mitsubishi WS-55807 TV

Not finding what you are looking for?
Sony KP-53V75 53" Rear Projection Television Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76287 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1691 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...