E24 error Machine keeps turning itself off. E24 error

The E24 error code for the Juki CP-130 sewing machine usually indicates a problem with the thread take-up lever. Some common causes of this error include a thread take-up lever that is not properly installed or adjusted, a bent or damaged thread take-up lever, or a thread take-up lever that is blocked by lint or debris. To resolve the issue, check the thread take-up lever and clean it if necessary, and make sure that it is properly installed and adjusted. If the issue persists, you may need to have the sewing machine serviced by a professional.

https://www.bosch-home.com/us/experience-bosch/heart-of-the-home/tips-and-tricks/all-articles/e24-error-code

The E24 error code indicates no drain flow possible. This means that the drain pump is running but unable to remove the water, or drain system blockage. Check for blockage of drain hose and drain pump. ... We have replace the water intake valve and the water pump.

https://bosch-dishwasher-errors.com/bosch-dishwasher-error-code-e24/

Possible causes for the E24 error code:
The drain hose could be blocked
The dishwasher filter may need to be cleaned
Brand new garbage disposal. The installer may have forgotten to remove the 'knockout' plug
After fixing the problem, reset the dishwasher according to the owner's manual

Perhaps it would be best to contact Juki Support.

Problem with Juki DDL 5550N 7 Sewing Machine Error Code E24

...

Consult your owner's manual in the Troubleshooting section. Sounds like your machine is giving an error message.

...

I have a nissan urvan 1988 petrol E24 model..problem is in the

www.botsofprey.org/F/cars/t25797951-nissan_urvan_1988_petrol_e24
I have a nissan urvan 1988 petrol E24 model..problem is in the ... Good luck & keep in touch. , jack the car up and take a bar lift up on tire and ck ... My nissan urvan 2005model ve25 with a 2ltr petrol engine ka20 has difficult starts with a cold ... is displying a fan error when switching on and fan stays at max speed.. any help?

Unfortunately, it means you have a computerized machine that can only be repaired by a technician with proper diagnosing equipment. Even if you can find out the meaning of the code... that may not tell you what to do about it. (It usually involves replacing circuit boards). Monetarily, with regard to cost of repairs, we were all far better off back in the days of ''switches'', ''knobs'' and ''mechanical timers''.

El Drv se refiere a la tarjeta interna que controla el motor, est? se encuentra da?ada.
Email: [email protected]

ERROR E24:
Faulty drain pump or blockage.
Drain pump, pump's wiring or control board fault.
Pump's electrical resistance is incorrect.
This could indicate a short, open circuit or water ingress.
Try unplugging 15 min or so.
This will 'hopefully' re-boot the electronics circuit 'brain'.
Failing that, try replace parts one-by-one, starting with drain-pump.
If you stop washer full of water, it creates a heavy load,possibly stalling the pump
I'm not 101% sure, but 'stalled pump' could be the E25 error code also mentioned in question.
Remove water by hand or whatever means you can.
If you have an Aquavac-type vaccuum cleaner this works.
Check your filters are clear of water.
Remove the impellor cover then try to turn pump impellor.
It should be able to turn easily.
If not, pump is stuck.
The impellor cover is a small plastic cover secured by a single screw, located at the bottom / side of the machine, usually at the back or left.
An 'impellor' is technical gobbledegook for a water 'propellor' or 'fan' to drive water by centrifugal force.
Technical terms designed to confuse people LOL. :)
All done?
Refit the cover and try the machine again.
Hope this helps,
Clive.