Question about LG WM-1832C Front Load Washer

2 Answers

LE code Washer is half full of very wet laundry and stopped filling. LE code popped up. Tried to restart but the washer light flashed and the LE code popped up again. Sometimes there is a little leak from the washer.

Posted by Curly top on

  • Thorjurgen Nov 02, 2007

    Washer is full of very wet laundry and stopped spinning half way through cycle. LE code
    popped up and machine went idle. Turned power off, removed half of the laundry and started up again. This time it finished cycle. However, next time it failed again and now the LE code is constant.No apparent leak. Manual solution not encouraging - instructs to turn off power, turn off water and call for service. Oh no.

×

Ad

2 Answers

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 100 Answers

LE error is a locked rotor you need to have your hall sensor on the stator or better yet just have the whole stator replaced which comes with the sensor on it (P.S. the stator is part of the motor and has a 5 year warranty)

Posted on Oct 30, 2007

Ad

Jim Gillon

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 77 Answers

Stator is not covered by warranty if the problems was sensor.
stator doesn't go bad unless someone damaged it.

Posted on Nov 27, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it beep through the entire. Wash cycle. No code showing.


Whirlpool Duet GHW9150P Front Load Washer Beeping ...

www.fixya.com > ... > Whirlpool Duet GHW9150P Front Load Washer
Question about Whirlpool duet Washing Machines ... my front loader is not workingwhirlpool washer flashes and beeps will not finish a cycle 1 Beep/E10--Error: Water... It beeps through the wash and rinse cycle every couple of minutes. ... Cycle signal which tells you that the cycle is complete beeps through the entire cycle.

[PDF]front-loading automatic washer use and care ... - Whirlpool

www.whirlpool.com/.../U...

Translate this page Whirlpool Home AppliancesWash. This is the main portion of the wash cycle. You will see the washer tumble the load. ... Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again. .... Using recommended AFFRESH® washer cleaner, add.

[PDF]DISHWASHER USER INSTRUCTIONS - Whirlpool

https://www.whirlpool.co...

Translate this page Whirlpool Home AppliancesThe first cycle using the sensor will run longer to calibrate the optical sensor. Rinse Aid. Using rinse aid will optimize your drying and wash performance. This dishwasher is ...... laundry detergent, hand soap, or dish detergent for hand washing .... models) you will experience more starts and stops throughout the entire cycle.

Continuous Beeping - Whirlpool Duet Sport Washer - The ...

appliantology.org > ... > The Laundry Appliance Repair Forum

Jan 25, 2016 | Whirlpool Washing Machines

1 Answer

Washer stopped, door is locked and LE is flashing on machine. What should I do?


it has detected a problem with the fill water
as the official description of the "LE" is:

The washer has tried to fill but has not reached the proper water level.
there can be several reasons for this to occur , the only one that the operator can ck is that the water supply to machine is connected and turned on , the others are a serviceman's call

Jan 18, 2016 | Samsung WF337AA Front Load Washer

1 Answer

LE light came on and washer stopped. Tried another load, washer filled but does not run


The LE code means a motor error. Lock error, you may have to try replacing the Hall Sensor and if this doesn't fix the problem then you need to replace the Stator as there may be aproblem between the Stator Assembly and the main PWB Assembly.

Nov 08, 2009 | LG WM2688HWM TROMM SteamWasher

2 Answers

Le error code


IE means that it is taking too long to fill up.

May 28, 2009 | LG WM-0532HW Front Load Washer

1 Answer

LG front load washing machine will not spin


I am having the same problem with my washer. Go to this web site below it has a free troubleshooting guide. I narrowed my washer machine down to two parts. Stator assy or Main PWB assy.


http://136.166.4.200/contents/Laundry/WM2042/WM2042xx_Service_Manual.pdf

Oct 10, 2008 | LG WM-1832C Front Load Washer

1 Answer

Washer


Product Laundry Washer
Symptom Error Codes
Sub Symptom LE error code
Question Locked motor error code.
Answer
LE error code: This indicates a locked motor condition. Please check the following conditions. Large loads of laundry can put a strain on the motor causing the LE error code. Try removing some clothing and restart. Excessive suds can cause the LE error code. Make sure the customer is using an HE (High Efficiency) detergent. They should decrease the amount of detergent until the machine washes without suds. A few bubbles can be expected. Areas that have �soft� water will usually need to use less detergent. If you suspect that excessive suds are the problem, let the machine stand for 30 min (motor cool down) and then run a rinse and spin cycle before restarting the load. If these directions are followed and the code persists, the machine will likely need service. .

please do not forget to rate and comment about your experience with fixya today.

Aug 18, 2008 | LG WM2277HSW XL Front Load Stackable...

1 Answer

Code LE comes on my washer it is a LG wm2075cw


Product Laundry Washer

Symptom Error Codes

Sub Symptom LE error code

Question Locked motor error code.

Answer LE error code: This indicates a locked motor condition. Please check the following conditions. Large loads of laundry can put a strain on the motor causing the LE error code. Try removing some clothing and restart. Excessive suds can cause the LE error code. Make sure the customer is using an HE (High Efficiency) detergent. They should decrease the amount of detergent until the machine washes without suds. A few bubbles can be expected. Areas that have �soft� water will usually need to use less detergent. If you suspect that excessive suds are the problem, let the machine stand for 30 min (motor cool down) and then run a rinse and spin cycle before restarting the load. If these directions are followed and the code persists, the machine will likely need service. .

Aug 17, 2008 | LG Washing Machines

3 Answers

LE Code on control panel


Press "end of cycle". Plug off the wall. Code can be an indication of several issues. The most common cause is over-sudsing in the machine. Overloading the wash with too much laundry may also cause the LE error code. Lastly, a breakdown in the signal between the microprocessor and the motor may cause that error code. This can occur if there is a loose wire, see that all wires are tightened..........

Dec 31, 2007 | Washing Machines

4 Answers

LE code flashing


Try replacing the sensor assembly. Part number 6501KW2002A. It is on the stator itself where the 4 wire connector clips to. Only costs $17 + change & shipping. Mine works fine now!

May 07, 2007 | LG WM-1832C Front Load Washer

Not finding what you are looking for?
LG WM-1832C Front Load Washer Logo

725 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85231 Answers

Cindy Wells

Level 3 Expert

6082 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...