Question about Line 6 Flextone III Plus Guitar Amplifier

1 Answer

Flextone 3 one speaker not working - Line 6 Flextone III Plus Guitar Amplifier

Posted by mike covert on

Ad

1 Answer

rhodesworks

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.

  • Line 6 Master
  • 3,157 Answers

Then you either have a blown amp or speaker. Turn the amp off and move the wires from the speaker on the working side to the other speaker. If the other speaker works, you have a dead amp channel. if it does not, move the wires from the speaker on the non-working side to the other speaker. If that works, you have a dead speaker. Dead amp channel means take it to the shop. Dead speaker means buy a new one from Line 6 and install.

Posted on Nov 25, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Line 6 flextone 2 tuner collaboration
ask the same question on "You Tube Broadcast". pretty much every answer u need for line 6 is right there. and w/ a video. someone turned me on to that a few mos. back. wow save me so much time. crazy. good luck!

Sep 17, 2014 | Music

1 Answer

Speaker not working
try switching the leads on each speaker. if sound transfers then you have a bad channel. if you get no sound, then your speaker is bad.

Mar 08, 2014 | Line 6 Flextone III Plus Guitar Amplifier

1 Answer

The parameters shift up and down while playing
if you're using a pedal. the cat 6 wire that connects the pedal to the amp. can be coming out of the "phone jacks" that line 6 uses, all it takes is for that wire to stretch and if one line breaks . it changes the protocol. sounds like yours is intermittent. put new connectors on each end (after checking continuity),

Sep 03, 2013 | Line 6 Flextone III Plus Guitar Amplifier

1 Answer

With my flextone III on start up all the lights come on and no sound. I've tried the factory reset precedures and software upgrade, not the line 6 monkey program, but the midi in and out shows no...
If it has 2 fuses, the second one might be blown. Try replacing the fuses, if its not that then there is a problem with the amp and you will probably need to take it for repairs.

Jul 01, 2011 | Line 6 New Line6 Flextone Iii Xl Amp

1 Answer

The entire control board on top of the flextone III amp (volume controls, bass, treble, model selector, effects, etc..) is lit up and unresponsive. I tried a factory reset by holding a & d down for 8...
There is probably a power supply failure or with the power on reset circuit. Likely low voltage to the logic electronics. This is NOT DIY unless you are familiar with electronics.

Apr 22, 2011 | Line 6 Flextone III Plus Guitar Amplifier

1 Answer

I bought a used line 6 flextone 3 guitar amp but need a manual to know how to preset the 32 different amps that it models after. can i download the manual? and if so where?
Google is your friend to find the download:

http://line6.com/support/manuals/?families=7&submit=Submit&1st=1st

Feb 13, 2011 | Line 6 Flextone III Plus Guitar Amplifier

1 Answer

I have a Flextone II XL 212 combo. When I mute the strings it's quiet, but when I play there is always a hum/buzz with the note on any voice or preset. I've tried different guitar and cord. It's not a...
You have analyzed the problem... with the strings muted, the unit is quiet... that means the problem is with the guitar or cable picking up the noise. Move the guitar around near other things to search out the source which is probably magnetic fields... orient the guitar differently to sniff for the source. OFTEN lamp dimmers generate higher frequency components that can couple into the guitar pickups. The problem is fairly common.

You likely are in an area that has magnetic fields. Also you may have the settings on the amp that accentuates the noise. Eliminating this noise, especially at low levels, can be difficult if you have devices like flourescent lights that have magnetic ballasts.

You might also try running a different source into the amp such as a walkman player to verify the audio can be cleanly amplified. If that works, then the amp is OK.

Nov 26, 2010 | Line 6 Music

1 Answer

Plugged my fbv Shortboard into my Line 6 Flextone iii and all the lights went red with no lcd read out.
Try plugging it in and then turning on your flextone, or vice/versa. If not than post it on the line 6 website, they have techs look at those problems all the time.

May 20, 2010 | Music

1 Answer

My Line 6 Spider Amp sound goes out when I plug in my FBV express pedal. Any advice?
Read this cut and paste and verify compatibility as a first step:

<<<
*FBV is not compatible with Spider II 15 or Spider III 15.

**FBV is only compatible with POD 2.0 units with pedal jacks labelled "FBV Pedal." It is not compatible with older units which have pedal jacks labelled simply "Pedal."

(NOTE: FBV is NOT compatible with Ax212™, Flextone™ I, II or HD, POD® Pro, Bass POD®, Bass POD® Pro and Spider™.)
>>>

Note there are apparently several versions. Check compatibility at this site:

http://line6.com/footcontrollers/fbv.html

May 07, 2010 | Line 6 Spider Iii 120 Stereo Guitar Combo...

1 Answer

I have a Line 6 Flextone III XL. I plugged in my guitar and the sound cuts in and out. It fades in and out. I checked the cable and try using another cable, samething. If I play with the cable by moving...
If the sound "fades" in and out that implies a SLOW change in volume.

If that is what you have, it is likely that there is a problem with the power input or power supply as these are the only thing that would have a time constant to react SLOWLY. Fortunately, this area is one of the easier ones to find and fix.

Dec 07, 2009 | Line 6 Music

Not finding what you are looking for?

View Most Popular

Flextone III Plus Guitar Amplifier

  • Music

Related Question

Line 6 flextone 2 tuner collaboration

  • Music

Open Questions:

0 Answers

Baldwin EP 101 has loud noise when you power it up.Notes will not play. What area controls the tone generator?

Feb 24, 2021 | The Music

0 Answers

How can I rewire my first act 222 Adam Levine guitar pickups?

Feb 08, 2021 | First Act Music

0 Answers

Europort EPA300. Why is there no panel illumination in Effects/Treble/Bass Level section and no control operation? Not getting full sound. System used for karaoke and outdoor music

Dec 22, 2020 | Behringer Music

0 Answers

MG50CFX. Why is fx loop almost silent? No sound from Boss CE-5, nemesis delay, or rack mount Lex mx-200

Dec 17, 2020 | Boss Music

See all Line 6 Flextone III Plus Guitar Amplifier Questions

Related Topics

Line 6 Flextone III Plus Guitar Amplifier Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1 Answer
Pocket Pod wont turn on

Line 6 Pod 20 Fx Box

1 Answer
How to use the tuner on Spider IV 15 amp

Line 6 Spider Iii 15 Modeling...

1 Answer
How do you reset your

Line 6 Spider Iii 75 Guitar...

2 Answers
Amp turns on but no sound even with diff guitars and cords

Line 6 Spider Iii 15 Modeling...

2 Answers
My spider III amp has no sound.. lights on but no sound

Line 6 Spider Iii 30

Top Line 6 Music Experts

Real Cool
Real Cool

Level 3 Expert

33537 Answers

rhodesworks

Level 3 Expert

3157 Answers

Joel Bing
Joel Bing

Level 2 Expert

56 Answers

Are you a Line 6 Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...