Logik l39fe12 common power supply faults - 2004 Mustang Factory Wiring Diagrams

The error code H on a Logik L614WD13 washing machine means that there is a problem with the motor. The most common cause of this error code is a faulty motor, but it can also be caused by a problem with the motor control board or the wiring harness. To remedy the error code H, you will need to identify the underlying cause of the problem. If the motor is faulty, it will need to be replaced. If the motor control board or wiring harness is faulty, they will need to be repaired or replaced. If you are not comfortable troubleshooting and repairing electrical components, you should contact a qualified technician to fix the error code H on your Logik L614WD13 washing machine. Here are some additional tips for troubleshooting the error code H on a Logik L614WD13 washing machine: Check the power supply to the washing machine to make sure that it is turned on and there is no power outage. Check the fuses or circuit breakers that supply power to the washing machine to make sure that they are not tripped. Disconnect the washing machine from the power supply and then reconnect it to see if the error code clears. Listen for any unusual noises coming from the washing machine, such as a humming or buzzing sound. Check the motor coupling to make sure that it is not loose or damaged. Inspect the motor for any signs of damage, such as burnt wiring or a broken fan blade. If you have checked all of these things and the error code H is still present, then you will need to contact a qualified technician to diagnose and repair the problem.

The main cause of this problem is a faulty power supply. Here, you need to check the plug fuse, mains lead, and the wiring inside for faults. The problem could also emanate from a faulty mains power supply.

If the set do not switch ON; the main power supply regulator board is not working. You can't detect its fault visually. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Fault with the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and precious time.

Fault with the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/

Err7 - Logik washing machine
This fault is very likely one of these things
1) Quite uncommon - Mentioned above - the wiring . Check the plug to the motor is firmly in place and no wires are broken. You could also disconnect the plug and visually check it for any signs of burning due to a bad connection
Very easy to do
2) Not very common - The motor itself has bunt out. Visually check the commutator for signs of burning . Other than this it's a case of using a multimeter to find if there's a circuit through the coil and if the motor is getting any power in the first place Visual check is easy but you will need to have/know how to use a multimeter for the rest

3) Very common and most likely the cause of your fault - The carbon brushes on the motor. Pull the machine out from under your worktop and tilt the machine backwards so that it is at an angle that you can get underneath. A good tip is to lean the machine back in the space you pulled it out from and tilt it so that the worktop holds the machine at an angle for you if that makes sense. This way you can work without anyone having to hold the machine at an angle for you.
Now get on the floor and from the front look under your machine and you will see the motor. On the motor there are 2 black plastic parts each with 2 screws holding them to the motor. These are the carbon brush holders. Undo the screws on each holder being careful not to drop them . The holders will now come loose. Carefully pull the wire off each and you can take them off the motor. The carbon itself is the part that makes contact with the commutator and it is spring loaded to ensure that connection is made, however, when the carbon gets too worn that contact cannot be made therefore your motor will not turn. To tell if the carbon brushes are worn it's just a case of a visual check. If the exposed amount of carbon is less than 1cm long this is your fault. Change those carbons and I'm almost certain you will have fixed your machine Fairly easy to do and a very common fault

try turning off AND unplug for a couple minutes! USB may have pulled power down to start the switching noise. Try usb again and if it does it again then I wouldn't use that usb anymore.

058,055,028,025. Try these codes. For more information http://electrohelponline.blogspot.com/ Setup procedure, and setup code list to many popular remote controls are given. Pull up older posts.

Here is a helpful YOUTUBE link that will help you focus/find your problems...


LCD TV Repair No Power Power Supply Common Symptoms Solutions How to...

MAYBE this SECOND Link is better for you?

Anthony Free repair help to mend and fix any fault how to mend it com

A