Kyocera Mita FS-820 Laser Printer Logo

Question about Kyocera Mita FS-820 Laser Printer

1 Answer

Kyocera FS-820 LEDs are Blinking. Suport says, waste toner ist full. Sent to support. Where ist the waste Toner box? How can I empty the Box? Thanks.

Posted by j_heberle on

  • Anonymous May 11, 2010

    Are you sure it's a fs-820...I don't recall them having a waste bottle

×

Ad

1 Answer

versa093

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

As far as I know this is a new pcu required

Posted on Jun 11, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Replace new toner and displeyd mesages "chesk waste toner box". i remove waste toner box and cleaned waste toner in drum unit. no result...

the top of the waste toner container must be cleaned 100% from the toner because it should be a light sensor that has to pass through it , if its spoiled with toner the light cannot pass through it ,so i recommend you to empty the waste toner container first and wash it with water and drying it well before using it again.
tip

Toner Box full when its not - fault

Putting a small lump of bluetac on the inside of the door will push the waste toner collection box into the correct position and stop the empty the toner box fault.
As the toner box is not seating in the sensor correctly.
0helpful
2answers

Message on screen says "Waste Toner Box Full"

Typically you will need to replace the waste toner box. There is usually a difficult to access part of the bottle that is used by an optic sensor to tell when the box is full. Plus toner is very fine and you do not want it getting into the air. Toner will pass through the filter of most vacuums and go back into the air.
1helpful
1answer

Waiste toner box full.....how do I clean or change this? Looked through owners manual and can't find anything about it.

The waste toner sensor has detected
that the waste toner reservoir (drum unit)
is full.
FS 1128 has drum and developer as separate unit, waste toner gets collected in the drum unit . Right or left side of the drum unit has a cap fasted with screw, open it and remove the waste toner.Refix the drum and this will solve the probelm
0helpful
1answer

Where is the waste toner box on the Kyocera FS-3830N printer?

facing prnter look on left side. midway of side panal theres a door. push tab on door to the rear of printer a bit and door should open. depress plastic tab on neck of toner coleection bottle and pull out full bottle. replace or empty an dreinstall and cloe door. should reset and restart to ready condition.
3helpful
1answer

Waste toner gets full before toner runs out

Actually, the waste toner should get full sometime before the regular toner runs out in laser printers that have several toner cartridges compared to the single waste toner reservoir.

You can dump the toner reservoir out and avoid buying the empty waste toner 'reservoir.'

I did this on my Brother Laser printer and saved about $30 or so for an empty plastic waste toner bottle or jar.

If this is the way the Kyocera-4020DN is, then I would put the waste toner, which is just that, waste, and put it into a plastic zip loc storage bag and throw it away. Don't breath the toner.

Good luck on this repair.
3helpful
2answers

Check waste toner box

We have a Kyocera Mita FS-3820N and sometimes when the toner box message does not go away, even after emptying the box, we simply hit it a few times in the area of the box. Works every time!
1helpful
1answer

Self test says 'check waste toner box'

It looks your waste toner box is full. Waste toner box collects toner drawn during printing. You have to remove waste toner bottle and empty it.

Follow the instructions to clean up toner bottle
http://www.kyoceramita.co.th/news/products/img_promain/20091141129533.pdf

Hope this helps
4helpful
2answers

Kyocera Mita FS-1030D Laser Bottom 2 lights blinking.

I think the two lights flashing together indicates waste toner box missing or full but as this printer doesn't have a waste bottle I assume it means the processing unit (ie the drum bit) needs replacing.
Not finding what you are looking for?

978 views

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

7025 Answers

Clive
Clive

Level 3 Expert

4362 Answers

Are you a Kyocera Mita Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...