I just got an itouch and when i went to access the internet, it told me to enter a password to access belkin54g. so i went on the belkin default page on my computer and i successfully logged in and i dont know where to go from here to reset the password, and i dont want to reset the device. could someone give me simple, easy to understand instructions as to how to gain internet access to the itouch? please and thanks (:

Connect a LAN cable from Belkin to your laptop/computer's LAN port, open a browser on your laptop/computer and enter the Belkin's configuration URL. http://192.168.2.1
The default PW = blank (just press Enter) You can now change the default admin password.
You can now configure the wireless settings to protect your wireless network and Internet from unauthorized access. Now configure the wireless card in your computer/laptop with the router's wireless settings. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

If you can still remember the password that you entered on the configuration page, follow the steps below:
1. In the lower right corner of your screen (near the time and date), right click on the wireless network connection icon, then select view available wireless networks. Or, if your wireless adapter has its own wireless utility, you should see that in the lower right corner of your screen.
2. You should see the router's wireless network name (SSID). By default, the SSID is "belkin54g". Select the SSID and it will prompt you for the network key.
3. The network key is the password that you entered on the router configuration page.

If you cannot remember the password that you entered, follow the steps below.
a. Connect your computer to the router using an ethernet cable.
b. Access the setup page by typing 192.168.2.1 in the address bar.
c. Go to Wireless -> Security. Copy the network key.
d. Then follow steps 1-4 above.

For the MAC computer:
1. From the Airport menu, select the SSID.
4. When asked for a password, enter the network key that you entered on the router.

I hope this helps!

default username and password is admin for both.
Otherwise press and hold reset button for 5 seconds on the back of the router and reset it
You can access router via ethernet cable by bringing up an internet page and type 192.168.1.1

reset your Router via pin whole at its back then set the config of TCP/4 and obtain Ip automaticaly and obtain DNS automaticaly... later set your settings according by 192.168.1.2 without changing IP and then turn off you router ... turn it on after 5 to 10 min .. thank you

1. Click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections.
2. Right-click the network connection that you want to configure, and then click Properties.
3. On the General tab (for a local area connection), or the Networking tab (for all other connections), click Internet Protocol (TCP/IP), and then click Properties.

1. Check the option which says use the following ip address and enter the ip address that you have forced in the belkin router, type the subnet mask 255.255.255.0 and enter the default gate way the ip address of the belkin router (ip address that you use to open Belkins page)

If you have the documentation on this router you might be able to default the router to its factory settings and access the router with the default login/password.

goto start>>
click run
type cmd
type ipconfig
check what is ur default gateway
then goto internet browser
type the default gateway in address bar on the web browser
YOUR belkin router homepage will come up
If it asks you for any username and password
U will have to contact belkin to get that...
after entering the username and password
u will be able to check the configuration setings

There is no default WEP / WPA key for belkin54g routers. The default password to access the setup is blank. Try going to 192.168.2.1 in internet explorer (where you would usually type the address of the site in), and see if you can find out the WEP / WPA Key.

Hi,
First make sure you can see the router in your Available Networks. You can do this by double clicking the Networks icon at the bottom right hand corner of your screen.
If you can see the router on the list, double click on it, and if it is unsecured, then you should be able to connect to the internet. If it is 'secured', then you have to enter the Username and Password to gain access.
Or you could type 192.169.0.1 into your internet browser URL box on the laptop. This will ask for the same Username and Password. The default Username is usually 'admin' and the default password is usually 'password' (or 1234 on older models). If successful, you should be able to see the routers settings, and diagnose if your router is properly connected to the internet. If it seems to be connected, and the Username and Password are being entered properly into the laptop when you try to connect to a network, then it can only mean that the laptop's wireless card/adapter is not configured properly on the laptop.
I hope that helps :)
Chris

@boblawrence6
Read page 14 from the users manual to reset the custom password & other settings.
Users manual at > http://www.belkin.com/support/product/?lid=en&pid=F5D8233-4
find the default Password at > Page 24 and reconfigure your router settings.
@munchx3mom
Surf to > http://www.belkin.com/support/product/?lid=en&pid=(CHANGE THIS WITH YOUR PRODUCT ID) *F5D8233-4*

Best regards
Screbilde