Night Owl Optics Cyclops Compact NOCC3 Monocular Logo

Related Topics:

A
Anonymous Posted on Feb 23, 2014

System turns on and works great for about 5 min with fresh batts after 5min shuts off will not turn on until I put another fresh pair in.. what is the cause and can this be corrected?

Would like anything on this..what would be the norm on batt life?

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My JVC Ha-s20bt doesn't want to pair with my device.. any help would be greatly appreciated. Headset pics up in my Bluetooth list but when I click on it, it asks me to pair, I click yes and then it says...

1. Check that the power is turned off

power lamp off s20_dntxilxgecvgvp-undefined-undefined-0.png 2. erform one of the following operations depending on the connection status. When connecting for the first time
Hold down button for 3 seconds until the indicator flashes alternately in red and blue.
When there are 2 or more the BLUETOOTH devices to connect to
Hold down button for 5 seconds until the indicator flashes alternately in red and blue.

connecting_s20bt_jeawiluqvwxlgs-undefined-undefined-1.gif
3. Turn on the Bluetooth function of the BLUETOOTH device.


connecting 2 new_dntxiljgmiiddj-undefined-undefined-3.png

4. Select "JVC HA-S20BT" from the device list.


connecting 3 s20bt_dntxilmycugtzm-undefined-undefined-10.png

5. The indicator flashes slowly in blue when a connection is completed.

blue_flash_s20bt_jeawilhopkechq-undefined-undefined-15.gif

Please note :

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter "0000" as the PIN code for the System. If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
0helpful
1answer

Will run great for about 5min at full throttle then will start to miss on one or two sounds like turn off and fish hr.or so then start up and it will run great again for 5 mins and do it again (help)

Common problem is water pump impeller is bad. Should be checked every spring. When water pump isn't providing enough water to cool motor, thermocouple in motor will stop motor to avoid damage. When motor cools, it will restart and run until it overheats again.
Mar 03, 2018 • Boating
3helpful
2answers

My Lancer shuts it self off at low idles after it warms up. I adjust the throttle so it wont shut off and now it refs from 800rpms to 1.5rpms after the car warms up. Any ideas at where I need to look?

when u adjusted the throttle did you reset your system set it to around 750rpms let it run for like 5min turn off unplug the battery both wires pos and neg for 5 mins put back and try again it should level out if not bring it to a shop could be something deeper or a o2 sensor
0helpful
2answers

98' Cav.. Drove it to store, shopped, didnt leave anything running or turned on. Went to car, opened dr...no dome light (thought, hmph, must have burned out -- fix later). Tried to start car... I turned...

this sound to me like at first I thought it was a fuse, as the problem went on it shifted more toward a weak cell in the battery, if a weak cell sits for a little while the battery will not hold the charge in that cell and that will cause loss of power, "its charge", in tne other cells. you had mentioned you used another battery and it ran great but when the battery was removed, things went wrong. You may check to see if there is water in your battery
0helpful
1answer

If i state car for 5 min and shut it off it want start again

your car needs tuneup-chec distributor-plug wires etc-these things wear out from heat n voltage-the dist cap is probly corroded-also inspect fuel system-
1helpful
1answer

Ryobi SS30 starts great, runs fine, quits

the engine is getting to hot & shutting down either not the right fuel mix or not enough oil in engine sometimes the mixture screws need to be adjusted
3helpful
5answers

Krzr k1m won't connect to bluetooth device

Turn off the phone. Remove the micro-sd card. Restart phone. It should connect now.
Not finding what you are looking for?

75 views

Ask a Question

Usually answered in minutes!

Top Night Owl Optics Optics Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66949 Answers

Tony Parsons
Tony Parsons

Level 3 Expert

6405 Answers

Are you a Night Owl Optics Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...