Print Mode Error - Kyocera CS-2550 Black and White Copier

Doesn't like your paper size?

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00L4-91KewA3vebAYh7Dj9eIe5b7A%3A1610830848662&ei=AFQDYMLlJ4uz5NoP-YqVwAc&q=kyocera+print+mode+error

Google

make model manual

look at the troubleshooting section or use CTRL+F and type 'print mode error', press enter.
..

turn off machine, unplug network cable turn it back on with cable unplugged,if it clears error then you have a corrupt print job or dont have paper loaded job needs to print, clear your print queue or load correct size and type of paper print job is asking for

Hi,
I think you are seat only one print one time so plz check it. Go to printer option and setting. One time you check printer after your printer which mode show like active print mode, print error, hold print mode etc.
I suggest you Full uninstall printer driver and re-again install printer driver. If not solved then change printer cable.
If more help contact Dell printer Support Technician. and TechSupportPrinter expert team.
Thanks.

Print Mode Error is Chenglish for a problem with printing. Press the Print key at the left side of the panel, then the display should tell you to add paper etc

There are a few things to figure out here from a SAP basis administrator perspective these steps are common. Also I am just trying to help and with SAP there could be multiple solutions. Good luck.

Check SAP MarketPlace for SAP note: 1557674

Here are the steps taken from the SAP Community Network which might help. I would suggest reading the entire link as its informative. http://scn.sap.com/thread/1975158
Step:
run SPAD
to create an output device, choose Output Devices on the Devices/Server Tab
click on Display now you will be in Spool Administration window
click on Change button then Create tab will be appear, now you have to put the following information.
Under DeviceAttributees
put the Output Device name with shortname
Device Type: SAPWIN
Device class: Standards printer
you can put Model/Location/Message as per concern.
Under Access Method
Access Method: G
Host Printer: __default
save
for more information about
Device Type
http://help.sap.com/saphelp_nwmobile711/helpdata/en/d9/4a910f51ea11d189570000e829fbbd/content.htm
Access Method
http://help.sap.com/saphelp_nw70/helpdata/en/4f/9c033cff903105e10000000a114084/content.htm
(1) Choose "S: Print Using SAP Protocol" if a print server with SAPlpd or SAPsprint is used to print barcodes.
(2) Choose "F: Printing on Frontend Computer" if SAPlpd and SAP GUI are used together to print barcodes, SAP GUI sends print job to SAPlpd, SAPlpd is started automatically and forwards the print data stream to the Windows print manager.
(3) Choose "G: Frontend Printing with Control Tech", only SAP GUI is involved in printing barcodes, SAPlpd is not used.

Here are the Intermec drivers:
http://www.intermec.com/support/downloads/index.aspx

Understanding the LED Indicators
LED Meaning
Green (blinking) Auto-Sensing mode
Green (blinking) Downloading font, form, or graphic
Green (solid) Dump mode
Green (solid) Ready mode
Green (solid) Print mode
Orange (solid) Boot mode
Red (blinking) Media jam, overheated print head or stepper
motor
Red (blinking) Downloading firmware
Red (solid) Error mode

Good luck

You have turned the key before you finished in the previous mode. Turn the key until the mode error stops (not counting the off position). That is the mode you need to finish. Try pressing SUBTOTAL in this mode and then turn the key

print mode error is as a result of the size of paper not matching with paper in the cassette. When printing go to properties and select A4 before sending your print job

Try:

• ERROR LED: E, 1, 9
• ERROR LED: E, 2
• ERROR LED: E, 2, 2
• ERROR LED: E, 2, 3
• ERROR LED: E, 2, 4
• ERROR LED: E, 2, 5
• ERROR LED: E, 2, 6
• ERROR LED: E, 2, 7
• ERROR LED: E, 2, 8
• ERROR LED: E, 2, 9

1 Resolution may vary based on printer driver setting. Color ink droplets can be placed with a horizontal pitch of 1/4800 inch at minimum.
2 PPM print speeds are based on the highest speed printer driver mode. Photo print speeds are based on the default mode driver setting using Canon Photo Paper Plus Glossy paper. Print speeds will vary depending on system configuration, interface, software, document complexity, print mode, types of paper used and page coverage. CPM copy speeds based on fast mode setting using plain paper. Copy speeds may vary based on document complexity, copy mode, page coverage and number of copies.
3 USB 2.0 Hi-Speed requires Windows XP, 2000 or Mac OS X operating systems. For Windows 98, Me and Mac OS X v.10.2 to 10.2.6 operating systems, the printer will operate at USB 1.1 specifications.

The printer needs to have RAM drive off, mopier mode disabled. Also the device settings for the printer needs to have Printer Hard Disk set to not installed and job storage and mopier mode set to disabled.

try setting the driver to KPDL mode in the settings section of the driver