Question about Mintek MDP-1810 Portable DVD Player

1 Answer

DVD model MDP 1760

Using sharp tv as monitor, get sound but no picture on tv.  Is there a certain channel (I have used 3 and 4) that the tv needs to be on?  Is there something on the DVD I need to adjust

Posted by Linda Hopper on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the video from your dvd player to your "video in" on your set

Posted on Oct 17, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AOC L24H898 - Several problems. 1)Only 3 Display modes - AV, HDMI, PC. 2)In PC mode screen is white with barely-discernable Desktop. 3) Menu button does nothing (pressing Channel + and - together lo


This sounds like a common problem on these TVs (it's happened to both of my AOC TVs a couple times). Try a factory reset:

1. Press and hold "Menu" and "Channel+" on the TV. (do not use the remote)
2. Using the other hand, press the Power button.
3. A small screen should appear in the top left part of the screen.
4. Using the remote, select "Memory Recall" and Enter.
5. Power off and reboot the TV and Computer.
6. Run channel auto-scan to regain the picture.

Nov 17, 2011 | AOC L24H898 24 in. LCD TV

1 Answer

I have a Samsung SyncMaster 933 HD TV that we are using for a video hookup. We have plugged the white and red RCA jack into the back but did not get a picture. Does this TV have to be on a certain channel...


The white and red wires are for sound only, you will need to connect a video source, usually a yellow wire.

What is your video source? dvd, computer, vcr, cable

Write back and i will help more

Lone99star

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee

Jan 11, 2010 | Samsung SyncMaster 913V 19" Flat Panel LCD...

1 Answer

Impossible to change channels, turn TV on, Power and Opc blinking


go into programming mode and search for channels   it will do this automatically to find all antennae and all cable channels    if this is hooked up to a receiver box then only channel 3 will be found or used    also most tvs are computerized these days and at times it will need to 'rebooted'     unplug the power and wait 10 seconds and plug it in again    this may have to be done whenever you are locked out from changing channels or using the volume controls

Nov 05, 2009 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

New TV won't ''talk to'' old VCR


using the magnovox remote, reprogram the vcr's channels. set it up to use cable not air. when the vcr was unlugged it lost it's channel memory. don't buy new cables, you're getting a picture and sound so that means your rca cables are ok.

Jan 20, 2009 | Sharp Aquos LC-32D40U Television

1 Answer

Distorted sound, great picture on a Sharp Aquos 42" LCD


i belive that it is the brodcasts problem there is nothing wrong with your tv

Jan 09, 2009 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

New Sharp Aquos LCD 46 TV


If you hooked up the satelite box to your tv Automaticly the Satelite box is the one who pick up the channels (from the satelite)
In this case your tv is acting as a monitor only. Try to connect your tv with HDMI cable or COMPONENT cable for best picture. Don't use RF antenna input to hook up your Satelite Box. Hope this Helps
J

Dec 28, 2008 | Sharp AQUOS 52" Flat-Panel LCD HDTV

1 Answer

Proview 3200 HD TV


as you are using the ch3 , have you previously scanned and locked in all the channels for cable,

Apr 25, 2008 | Proview PL913S 19" Flat Panel LCD Monitor

1 Answer

Lcd montior with tv box but no hdmi sound


in some cases certain manufacturers say in the instructions that when using s video with seperate audio, you cannot use the HDMI for the sound and sometimes visa versa, it's just the way the output is set up. Remove the other sound cable you are using for pc or tv and just use HDMI to confirm that the sound is re-enabled on the HDMI

Oct 02, 2007 | Sony Playstation 3 (PS3) Console

1 Answer

Sharp 27" tv


You got the right idea,use the ext.imput on you tv and use the vcr to change the channels,you can check the solder conections in the tuner ,ussually the ground gets loose after a while but if you are not too familiar with tv service and dont want put any money in this set use your vcr.If the quality of the picture is still good then is worth keeping it.Let Us know if you need more information.

Oct 30, 2006 | Sharp 27C-240 27" TV

Not finding what you are looking for?
Mintek MDP-1810 Portable DVD Player Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mintek Televison & Video Experts

Ekse

Level 3 Expert

13434 Answers

Brad Brown

Level 3 Expert

18186 Answers

The Knight
The Knight

Level 3 Expert

76280 Answers

Are you a Mintek Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...