Question about Toshiba 1360 Black and White Copier

1 Answer

Error c7 My Toshiba 1360 shows the C7 error code. After removing the fusing unit from the copier, I have checked the fusing unit thermistor and it gives 750Kohms at room temp, which decreases when heating up the thermistor. Could someone tell me what is its real resistance at room temperature (at 25°C} approximately?And where could I get a circuit diagram for the PCB3F632310 ? I will appreciate very much your help.

Posted by Anonymous on

  • Anonymous Oct 29, 2007

    I have followed your advice and after clearing the C7 error the scanner moves in one way then return, but the red wrench light of the copier is still blinking and the C7 code is still there. Even preheating slightly the thermistor the red light continues to blink.

    In fact, soon after the copier is powered on, the red wrench light blinks.

  • Anonymous Oct 31, 2007

    Finally, I did reset the C7 code. Everything you said for the C7 code reset was ok but in place of 87 you put the 89 number and it worked fine.

    Thank you very much for your help



1 Answer

Chuck Clark

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 33 Answers

You can reset the C7 code, hold down 0&8 power machine up. Then push 87 & print, change the number to 0 with number keys press interupt key, then press 0&9 @ the same time to exit. This should clear the C7. Let me know if you need more help.

Posted on Oct 27, 2007

  • Chuck Clark Oct 29, 2007

    you may have to the reset a couple of times. does the heat lamp come on for 1-2 minutes in start up, if the lamp does not come on the thermal fuse could be bad or lamp is bad. you can check these with a voltage meter, set in the ohms setting. let me know

  • alfabren Feb 14, 2011

    well done worked a treat, thank you



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does an error c7 means in toshiba photocopier 1360 ?

C7 could be nothing serious but it had to of happened three times before it quit resetting itself, which means it has happened to you before. This model has a tendency to throw this code for no real threatening reason, but it is there as protection for the copier and it's environment. You really should have a tech look at it for you, and not just reset it.
Switch on the machine, holding down 0 & 8 buttons, type in 89, press the green button, enter a 0, press green button again to accept the new value. switch off & then just switch back on as normal.

Sep 24, 2015 | Toshiba Office Equipment & Supplies

1 Answer

Toshiba 1360 C7 code. How expensive is it ti fix

With the unit off hold down clear/stop and 8, ad should apear push 89 start (display will read 03) then 0 start. tis should fix it. -Carl

Jun 11, 2010 | Toshiba 1360 Black and White Copier

1 Answer

Toshiba 1360 Copier

"C7" Faulty thermistor, thermal fuse, or heater element

Sep 16, 2008 | Toshiba 1360 Black and White Copier

1 Answer

C7 Eror Code

C7 Fusing unit not warming up properly. It can be the fuser is not in correctly, fuser connector not making good contact, defective thermistor, fusing lamp or thermofuse.
Hope that helps...

Jun 17, 2008 | Toshiba 6560 Copier

1 Answer

Wrench light on and c7 code appear

C7 is a Fuser Error......The hot part where the paper passes through before exiting the machine is known as the Fuser or Fixing unit etc.

There are 3 parts involved and any of which when they fail will give a C7 error code. The Heating Lamp,Thermisor or Thermal Fuse.

This is a live area of the machine so you wouldnt be advised to attempt a repair without at least a restricted electrical license.

More than likely one of the parts mentioned will need to be replaced and then the C7 error count reset through "08"

May 12, 2008 | Toshiba 1370 Black and White Copier

2 Answers

Toshiba 1360 copier

Turn it on holding down 0 and 8. Key in 89, press start. press 0, press start. Turn it off and on.

Mar 18, 2008 | Toshiba 1360 Black and White Copier

1 Answer


TOSHIBA 1210 C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse

Oct 25, 2007 | Toshiba 1360 Black and White Copier

1 Answer

Toshiba 1360 C7 Error Code

TOSHIBA 1310 C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse


The codes are good for several models.

Oct 25, 2007 | Toshiba 1360 Black and White Copier

3 Answers

Toshiba 1360

You should be able to retrieve a code for a malfunction by pressing down the clear/stop and 8 keys. then let me know what you get, and we will go from there.

Oct 22, 2007 | Toshiba 1360 Black and White Copier

Not finding what you are looking for?
Toshiba 1360 Black and White Copier Logo

Related Topics:

758 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Office Equipment & Supplies Experts


Level 3 Expert

727 Answers


Level 3 Expert

2239 Answers


Level 3 Expert

1363 Answers

Are you a Toshiba Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides