Question about Nordic Track NordicTrack Commercial 1500 Treadmill
Posted by Anonymous on
Posted on May 15, 2010
SOURCE: My Nordic Track T7si is
There is a reset button.Locate the reset button near the power cord. Set the button to the reset ON position.------slide the reset button off/ on.then see if that makes any difference.-------
But if that is not helping and display is freezing again n again then remove battery from the display panel board.Clean the battery and re-insert.If that's not helping, try with new set of batteries.If syill the same problem then is faulty control key pad board.Its shorting, it has to be replaced.------- On most machines when you press a button on the console you
get a beep sound. If you don't get a beep on the elevation up or down
and you do on the speed up and down, it could be the display overlay/keypad.
If you see the elevation go up on the display but the unit is not elevating
it could be the motor or wiring.
Or last but not least, the electronics not being
able to send the signal out of the electronics.---------
This should help.Thanks.Helpmech.
Posted on Jul 02, 2011
Please read you owner manual.
If you do not have please go to www.nordicktrack. com then customer service and then parts & manual, give you model, etc, and download free and read the section how to fold and viceversa.
Posted on Dec 09, 2011
Tips for a great answer:
Jan 14, 2016 | Exercise & Fitness
Jun 13, 2015 | Nordic Track Exercise & Fitness
Oct 08, 2013 | Exercise & Fitness
Oct 07, 2012 | Nordic Track NordicTrack Treadmill, A2550
Dec 09, 2011 | Nordic Track NordicTrack T5 zi Treadmill
Sep 24, 2011 | Nordic Track NordicTrack Elite 7500...
Ensure that the treadmill is plugged into a grounded outlet using the correct surge suppressor. Use a UL 1449 suppressor listed as a transient voltage surge suppressor (TVSS). It must be rated for 15 amps and 120 volts AC. Secure the services of an electrician if the outlet is not grounded, or move the Proform treadmill near a grounded outlet. Do not use an extension cord.
Insert the safety key fully into the display. Treadmills with keys are designed not to turn on without the safety key in place.
Find the circuit breaker on the front of the frame and make sure it is not tripped. The circuit breaker is a vertical switch on the 540S and a horizontal switch on the 540 Interactive Trainer. Press it to the "Reset" position, which will be labeled.
2. Reed Switch
Unplug the treadmill and remove the safety key.
Move the upright base of the treadmill down with the help of another person and lift the uprights so that you can get to the underside of the console. Use a Phillips screwdriver with at least a 5-inch shaft to remove the screws. There are five hood screws on the 540 Interactive trainer and four screws on the 540S.
Remove the motor hood to get to the small reed switch by pivoting the hood off the frame. Find the reed switch and magnet, which are on the left side of the pulley for both models.
Turn the pulley with your hand until the reed switch aligns with the magnet. There should be 1/8-inch gap between the two. Fix the distance so that it is 1/8 inch by loosening the reed switch screw and sliding it to the correct distance. Tighten the screw.
Reverse the directions to put the hood back on and the treadmill upright in the original position.
Check too:Optical Sensor. If have it
Sep 22, 2011 | Nordic Track NordicTrack Treadmill, A2550
Aug 03, 2011 | Nordic Track NordicTrack Treadmill, A2550
Jul 13, 2010 | Nordic Track Exercise & Fitness
Apr 05, 2010 | Nordic Track NordicTrack Treadmill, A2550
322 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: