Canon c2880 streak across width of 8 1/2 X 14 paper when printed

Just, Change the fuser film sleeve or Fuser Unit.
you will have a new ImageCLASS

Sounds as though the fixing film assembly ( FM2-1793-020 ) in the fuser has developed a build up of toner causing what is normally called offset. You may also have to replace the lower pressure roller ( FC5-7207-010 ) also. You will have to remove the right side covers, door, and then the fuser assembly. Rebuilding the fuser has some challenges until you've done it a couple of times. Good Luck.

The is blocked by dust on the side of the paper on the image unit that would have color associated with the print. Remove all the image units and clean all the laser glass. Replace those image units also if streaking as for the paper ensure correct paper side and media type.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

If you put Tray 2 in Tray 1's spot with the heavy stock in Tray 1 (now in tray 2's spot) and print from it, does the problem persist?

This may help...
http://www.support.xerox.com/support/phaser-7500/support/enus.html?objGUID=4538

I have the same streaks problem. Any solutions?

check the drum

Perform Print Head Alignment Instructions to perform a Print Head Alignment directly from the machine. If diagrams or ruled lines are misaligned, print head alignment is required. The print head alignment can be performed automatically or manually. If the automatic print head alignment does not work, adjust the print head manually. Automatic Print Head Alignment

1. Press <ON/OFF> to turn on the machine.
   
   
2. Load a few sheets of letter-sized plain paper in the auto sheet feeder.
   
   
3. Press the Open button to open the Paper Output Tray. Then open up and set the extension by pressing down the hollow on the front side.
   
   
4. Execute automatic print head alignment.
   
5. 1. Press <COPY> button.
      
   2. Press <Menu> repeatedly to select [MAINTENACE].
      
   3. Press the left or right cursor to select [AUTO HEAD ALIGN], then press the <OK>. (A pattern is printed and the print head is automatically aligned. It takes about five minutes to finish printing the pattern.)
      
      
      
      

Manual print head alignment

1. Press <ON/OFF> to turn on the machine.
   
   
2. Load two sheets of Letter-sized plain paper in the auto sheet feeder or cassette.
   
   
3. Ensure that the proper paper source is selected.
   
   
4. Execute manual print head alignment.
   
5. 1. Press <Menu> repeatedly to select [MAINTENACE].
      
   2. Press the left or right cursor to select [ALIGN PRINT HEAD], then press the <OK>. (The nozzle check pattern is printed.)
      
      
6. Check the printed patterns and use the left or right arrow to input the number of the pattern in column A that has the least noticeable streaks.
   
   
   
   
7. Press <OK> to move the cursor to column B, and then use the left or right arrow to input the number of the pattern that has the least noticeable streaks.
   
   
8. Repeat the procedure until you finish inputting the pattern number for column P.
   
   
   
   
9. When you have finished inputting all pattern numbers, press <OK>.
   
   Note: For columns A through N select the patterns with the least visible vertical streaks. For columns O and P select the patterns with the fewest visible horizontal streaks.
   
   
   
   <1> Example of the pattern with the fewest visible vertical streak
   
   <2> Example of the pattern with the most visible vertical streak
   
   
   
   <1> Example of the pattern with the fewest visible horizontal streak
   
   <2> Example of the pattern with the most visible horizontal streak
   

I hope it helps!!!

Your fuser is worn out. Needs to be replaced.

This can be one of two

Print cartridge (you can do it, replace toner cartridge)

or Fuser (needs to go to doctors)

stop a print half way threw to confirm that it is print cartridge, good chance it is.

Links to my previous post on this problem below

HERE and HERE

hi seems like your printer's head is considering retirement not much to do here sorry have a good 1