Pits pgm no

press the preset number then press the call button

You need to go into the programming mode and re-program the speed dealing, which is stored centrally on the CPU, I have one of these systems in my loft. Remember all programming must be done from a systepnone/handset.

If you're doing it from the proper phone and it's a TA series, press 0. What does the display say now?

Dial 2 digits for year month day, day of week (0 being Monday) hh:mm: and 0 for AM or 1 for PM and STORE. So, in my U.S. based box I'd dial 101015506401 STORE

Carl

That depends on what you have the phone connected to. There's a switch on the base that referrs to EMSS. It's a dual Panasonic SYSTEM phone or Single line cordless. The PITS-PGM NO? means you've pressed the PROGRAM button in the EMSS mode.

Carl

1. Press 'PGM'- "program" button.
2. Press "speed dial" button.
3. Select "station # " i.e. any button from 1-9 for speed dialing.
4. (make sure to make a note of this selected # against the corresponding tel # and /or the person's name)
5. Dial the complete (incl. 1 for USA or country code for other country tel. #s) telephone number to be stored for the selected speed dialing station #.
6. Press "PGM" button again to complete the storing of the tel #.
7. Test, after dial tone, by just pressing the selected station #

I actually found the "Installation Manual" to accomplish this. Switch the button on the top front of the phone to "Program". Then the screen will show a "PITS-PGM NO?" display. Type in "*" then "#" and it will ask you for the "PASSWORD". Type in your 4 digit password, the default one is "1 2 3 4". When you enter it in correctly, it will display "SYS-PGM NO?". This is where you can enter in the "number" associated with the task you are trying to perform. For speed dials, it was 001. For date and time it was 000. Using certain buttons on the phone you then navigate accordingly. Hope this helps!

Press PROG press a speed dial button (ie 13-24) dial 9 plus the number press STORE

Carl

To set time on KX-T7735:

Press (Program)
at "PITS-PGM NO?" press * then # then enter your password default "1234"
at "SYS-PGM NO?" press 000
at "Day/Time Set" press (SP-PHONE)
date is displayed on bottom with year flashing, enter year on keypad "09" for 2009/
press right arrow to make the month flash, press (AUTO ANS)/(MUTE) button to cycle through months.
press right arrow, then enter date on keypad.
press right arrow, and (AUTO ANS)/(MUTE) to cycle through days of the week.
press right arrow, then enter the hour.
press right arrow, then enter minutes.
press right arrow, and (AUTO ANS)/(MUTE) to cycle through AM or PM.
press (AUTO DIAL)/(STORE) to save the date and time.

and you're done =D

If it is displaying "101:" that is your extension. You can press the * key (with phone on the hook) to scroll your display through date and time formats and to display your extension.

When it says "PITS-PGM NO" you will need to press one of the buttons on the numerical key pad to choose a function to change.

Hope this helps!

1.Press PGM. The Talk/Batt Low lamp flashes.
2. Press SPEED DIAL.
3. Press one of the dialing keys (0-9) to store phone number. You will hear confirmation beep.
4. Enter the phone number you want to store (up to 20 digits)
5. Press PGM. You will hear a long confirmation beep and number is stored. Tall/Batt Low lamp goes off.
Do not allow more than 20 between each step of the procedure. If you enter a wrong number, press PGM and start over.