Question about Andis Agc Super 2-speed Clipper International 220-volt Dog Grooming Clippers

1 Answer

Single speed i have an andis agc2 speed and recently it was only working on a single speed therfore when i switch from speed 1 to speed 2 doesnt increase the speed. As i saw that the motor is running i tought the circuit board was gone. I have ordered a new circuit board and changed it but still the same problem,my question is the armeture faulty or maybe the new board ive bought is faulty? Thanks.

Posted by oliver abela on

Ad

1 Answer

adam adms

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 829 Answers

Maintenance must be done and clean the engine

Posted on Jan 25, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove blades from a AGC2 hair trimmer
If you look at the base of the blade at the bottom edge the is a black metal bar, push this in towards the blade and pull the nose of the blade away from the clipper.

Jun 03, 2014 | Andis AGC2 Hair Trimmer

1 Answer

Clippers wont turn off?
Sounds as though the switch is faulty on the circuit board you can purchase new Andis parts here Dog Clippers

May 23, 2014 | Andis AGC2 Hair Trimmer

1 Answer

How do I find what model my Andis pet clipper is
On the back of the clipper it should say something like AG, AGR, or AGC does it look like any of these dog clippers Dog Clippers .
Has it got a power cable or is it a Rechargeable? Also age is a good clue?

Feb 04, 2014 | Andis AGC2 Hair Trimmer

1 Answer

I need to know how to change my cord on my andis agc2 pet clippers
You can find instructions on the following link
Fitting Cable

May 26, 2012 | Andis AGC2 Hair Trimmer

1 Answer

I removed the blade assembly on the andis agc 2 by mistake,how do i fit back together it doesnt seem to fit
Instructions come in with a new drive assembly, basicly put the black end through under the metal frame first then push it down into place.

Apr 21, 2012 | Andis AGC2 Hair Trimmer

1 Answer

Do you have a user manual for Andis 2 speed dog groomers
http://www.andis.com/USA/service/PartsListUseCare.asp?div=Information

Sep 08, 2011 | Andis AGC2 Hair Trimmer

1 Answer

I have an Andis AGC 2 speed and I cannot figure out how to get the blade on and make it stay on when I turn on the clippers.
Ok you should be connecting the blade whilst the clipper is on this will ensure the blade engages with the clipper correctly, simply push the front edge of the blade into the clipper untill the latch has snapped into place.

Aug 19, 2011 | Andis AGC2 Hair Trimmer

1 Answer

Speed changes on it's own and sometimes it only has one speed. wondering if it is the motor or switch?
Neither the circuit board need jacking up with a washer either side or worst case a new Circuitboard.

Apr 25, 2011 | Andis AGC2 Hair Trimmer

1 Answer

I have an Andis AGC2 Pet clipper and 2 Shih Tzus! This is the 2nd set of clippers that I have had the same problem. It sounds like it is working but when you try to clip the hair, it doesn't cut. I took...
you need to replace the blade drive assembly every 4-6months if your a busy groomer.

Jan 06, 2011 | Andis AGC2 Hair Trimmer

1 Answer

My andes agc2 doesnt run. i opened it and noticed the round cylinder ( which says 105 GR) was not connected to anything. how do i hook it up?
This round cylinder is a permenant magnet and doesn't actually connect to anything, the only contact which matter are the copper wires connecting the circuit board to the Carbon brushes.
This may be as simple as a faulty cable check for power to the circuit board.

Jun 11, 2010 | Andis AGC2 Hair Trimmer

Not finding what you are looking for?

View Most Popular

Agc Super 2-speed Clipper International 220-volt Dog Grooming Clippers

  • Pets - Others

Related Question

How do I remove blades from a AGC2 hair trimmer

  • Andis AGC2 Hair Trimmer

Open Questions:

0 Answers

my leopard gecko is tilting her head. she doesn't eat unless i hand it to her. I've only had her for a week and a half. and she stays in her humid hide

Jul 10, 2019 | Pets - Others

0 Answers

Innotek m041101 basic dog shock collar, new but just stopped working..clean, new battery, used for 1 hr. on dog (worked)....what to do? Thanks

Jun 07, 2019 | Pets - Others

0 Answers

what is the ratio for fortune 500 insecticide for chicken fleas

Apr 11, 2019 | Pets - Others

0 Answers

can you give for saint bernard to sleep to clean a wound

Dec 08, 2018 | Pets - Others

See all Andis Agc Super 2-speed Clipper International Questions

Related Topics

Andis Agc Super 2-speed Clipper International 220-volt Dog Grooming Clippers Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2 Answers
Andis clippers are shaking and loud

Andis Agc Super 2-speed Clipper...

1 Answer
My Andis pet clipper not cutting

Andis Pets - Others

2 Answers
The mounting hinge will not raise on my clippers when I push up on the button below the blade

Andis Agc Single-speed Clipper...

1 Answer
My clipper smoked and now it wont run at all

Andis Agc Super 2-speed Clipper...

1 Answer
HOW DO I PREVENT MY ANDIS CLIPPERS FROM MAKING A LOUD NOISE AND SCARING MY DOGS? THE CLIPPERS ARE NOT UNUSUALLY LOUD WHEN THE BLADE IS REMOVED BUT HAVE NOW GOTTEN LOUDER AND LOUDER WITH MULTIPLE USES.

Andis RACD Pet Clipper

Top Andis Pets - Others Experts

Tom Chichester

Level 3 Expert

61336 Answers

Ruth summersides

Level 3 Expert

1488 Answers

Kardoc

Level 3 Expert

6126 Answers

Are you an Andis Pets - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...