LG 37LP1D 37 in. LCD Television Logo

Related Topics:

Question about LG 37LP1D 37 in. LCD Television

Open Question

Lg 32lv2500 power light blinks red twice and then stays amber

Power light blinks red two times then stays amber. sound is fine. DVD plays fine.

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 92 Answers

SOURCE: my lg 37lc2d tv power light blinks 15 times and

The power supply is a common fault on this model.

Buy a replacement from www.chsinteractive.co.uk

Not cheap though.

Posted on Sep 05, 2009

Testimonial: "I found the part on partstore.com replaced it and works like new. Thank you"

Ad

Anonymous

  • 1 Answer

SOURCE: No Sound, No Picture on LG 42LC7D

I do not have a solution but I have the same situation with my tv

Posted on May 25, 2010

Ad
caroldon

Donald DCruz

  • 17130 Answers

SOURCE: LG 55lh40 tv will not turn on. I REPLACED THE

Only a probe with a voltage trace can figure to the possible SHORT in the circuit board. You need to look for possible signs of heating which can be an indicator to a short . Also check for the secondary +B to the circuit, check the path that leads to the drive and see if there is high potential drop, if so check the drop to get an idea of the short. The list of probabilities can be more and so ONLY a good voltage check can pinpoint the case. Take consensus but do not replace board at high cost with just assumptions.

Posted on Oct 24, 2011

Anonymous

  • 96 Answers

SOURCE: LG 47LG50 dead....no red light, no blue light, no green light. It made a CLICK sound and went dead. Power Supply?

may be power supply need more information

Posted on Jun 04, 2012

SOURCE: My LG 37LG50 TV wont turn on ?

Are you certain the replacement power supply is good? A defective main board or power supply can cause this problem.

Posted on May 05, 2013

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Lg led tv has sound but no picture

suspect either a back light power board issue or main power board to back light board issue...also, is it under warranty ?
0helpful
1answer

I have a 32lv2500 e picture is working but the screen is red , i have replaced the main board and the led driver , till have a red picture on all inputs

It sounds like a panel fault. If you wish to get more details, check the site linked here. http://electronicshelponline.blogspot.com/ Selecting the view option, either to Mosaic / Time slide, can be selected by the drop-down list, at the top left of the display window, will make surf easy. You can also do a search, by type in the brand name/model number/IC used, in the search box at the top right of the display window.
Screen-shots to defective LCD panel are given.
0helpful
1answer

Blinking lights on HP MD6580n

Sounds like the power supply is overheating.
0helpful
1answer

What does hdmi is blocked mean

Hello!
HDMI blocked could mean, that one or more HDMI inputs are turned off. In WD- series DLP TVs it's possible to disable one or more inputs, which are not to be in use, to speed up signal source switching. Most of modern sets are constantly monitoring inputs and automatically recognizing "plug"n"play" signals. blocking any input would not cause TV to shut down.
Yellow(amber) light means: lamp door interlock switch is off or malfunction. green blinking: set is initializing, about to begin normal operation. So: quite possible that lamp has been replaced incorrectly or door is not tight intermittently. Last possible issue: door's interlock switch is bad. Take lamp door off and you will find the switch with blue lever on the left side of the door inside plastic compartment. Push it with your "pinky" or pencil carefully, then ask someone to turn set on. Make sure, yellow light is off, before do so. If set starts normally, observe lamp's activity: it should stay on and getting brighter, while you holding switch. If lamp stops working, while there is no "amber" light, then TV shuts off, red blinks, lamp is bad. I just had to replace lamp twice, due to defective batch of lamps with housing. 3rd time I replaced bare bulb and it solved the problem. But there was no "amber" issue!
good luck,
Alex.
3helpful
2answers

Set is an LG DLP model RU 52SZ51D. Set sometimes needs to power cycle 20 or more times to fire up. Other times 1 or 2. The red led turns to amber and flashes approx 55 times and then turns to red and...

I need to know titles of lights that blinks on tv while it trying to power up. There are Power, Lamp and Temp lights, let me know what light blinks, this will help me to diagnose the problem as I hate to guess like try this and try that.
Thanks.
2helpful
2answers

Red Light Flashes twice KDF-E50A10

Are you putting the lamp cover back in place before trying to turn the set on? The 2 blink error is a temperature error you might want to check the thermal sensor, is your lamp door warped?
1helpful
1answer
28helpful
2answers

Setting up 42lg3000 with sky and lg home cinema dvd system.picture and sound from dvd.poor picture and sound from tv speakers only from sky .please advise on correct wiring connections for this set up.TV...

i have same tv, this i was i did on mine. on the sky+ remote push tv and then press select + red button at the same time, the red light blinks twice, then push 1174 then power button.
Not finding what you are looking for?

302 views

Ask a Question

Usually answered in minutes!

Top LG Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Cindy Wells

Level 3 Expert

6589 Answers

Are you a LG Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...